ALBERT

Description: The all-sky direct radiative effect by anthropogenic aerosol (DREa) is calculated in the solar (0.3–4 μm) and infrared (4–200 μm) spectral ranges for six Mediterranean sites. The sites are differently affected by pollution and together reflect typical aerosol impacts that are expected over land sites of the central Mediterranean basin. Central to the simulations are aerosol optical properties from AERONET sun-/sky-photometer statistics for the year 2003. A discussion on the variability of the overall (natural+anthropogenic) aerosol properties with site location is provided. Supplementary data include MODIS satellite sensor based solar surface albedos, ISCCP products for high- mid- and low cloud cover and estimates for the anthropogenic aerosol fraction from global modelling. Since anthropogenic aerosol particles are considered to be smaller than 1 μm in size, mainly the solar radiation transfer is affected with impacts only during sun-light hours. At all sites the (daily average) solar DREa is negative all year round at the top of the atmosphere (ToA). Hence, anthropogenic particles produce over land sites of the central Mediterranean a significant cooling effect. Monthly DREa values vary from site to site and are seasonal dependent as a consequence of the seasonal dependence of available sun-light and microphysical aerosol properties. At the ToA the monthly average DREa is −(4±1) W m−2 during spring-summer (SS, April–September) and −(2±1) W m−2 during autumn-winter (AW, October–March) at the polluted sites. In contrast, it varies between −(3±1) W m−2 and −(1±1) W m−2 on SS and AW, respectively at the less polluted site. Due to atmospheric absorption the DREa at the surface is larger than at the ToA. At the surface the monthly average DREa varies between the most and the least polluted site between −(7±1) W m−2 and −(4±1) W m−2 during SS, and between −(4±3) W m−2 and −(1±1) W m−2 during AW. The DREa at infrared wavelengths is positive but negligible, especially at the ToA (

Description: Volcanic aerosols resulting from the Eyjafjallajökull eruption were detected in south-eastern Italy from 20 to 22 April 2010, at a distance of approximately 4000 km from the volcano, and have been characterized by lidar, sun/sky photometer, and surface in-situ measurements. Volcanic particles added to the pre-existing aerosol load and measurement data allow quantifying the impact of volcanic particles on the aerosol vertical distribution, lidar ratios, the aerosol size distribution, and the ground-level particulate-matter concentrations. Lidar measurements reveal that backscatter coefficients by volcanic particles were about one order of magnitude smaller over south-eastern Italy than over Central Europe. Mean lidar ratios at 355 nm were equal to 64 ± 5 sr inside the volcanic aerosol layer and were characterized by smaller values (47 ± 2 sr) in the underlying layer on 20 April, 19:30 UTC. Lidar ratios and their dependence with the height reduced in the following days, mainly because of the variability of the volcanic particle contributions. Size distributions from sun/sky photometer measurements reveal the presence of volcanic particles with radii r 〉 0.5 μm on 21 April and that the contribution of coarse volcanic particles increased from 20 to 22 April. The aerosol fine mode fraction from sun/sky photometer measurements varied between values of 0.85 and 0.94 on 20 April and decreased to values between 0.25 and 0.82 on 22 April. Surface measurements of particle size distributions were in good accordance with column averaged particle size distributions from sun/sky photometer measurements. PM1/PM2.5 mass concentration ratios of 0.69, 0.66, and 0.60 on 20, 21, and 22 April, respectively, support the increase of super-micron particles at ground. Measurements from the Regional Air Quality Agency show that PM10 mass concentrations on 20, 21, and 22 April 2010 were enhanced in the entire Apulia Region. More specifically, PM10 mass concentrations have on average increased over Apulia Region 22%, 50%, and 28% on 20, 21, and 22 April, respectively, compared to values on 19 April. Finally, the comparison of measurement data with numerical simulations by the FLEXPART dispersion model demonstrates the ability of FLEXPART to model the advection of the volcanic ash over the 4000 km from the Eyjafjallajökull volcano to Southern Italy.

Description: Aerosol products by AERONET sun-sky radiometer measurements combined with air-mass backtrajectories were analyzed to identify source regions and pathways of air masses carrying aerosols to south-east Italy, and to determine the dependence of aerosol mean optical properties on advection patterns. Aerosol optical depth (AOD), fine mode fraction (η ), single scattering albedo (SSA), asymmetry factor (g), and lidar ratio (Lr) at 440 nm were used to characterize aerosol properties. The analysis of 5-day-backtrajectories ending in Lecce on south-east Italy and referring to 240 measurement days of the 2003–2004 years revealed that 32% of the measurement days were characterized by air masses coming from all continental European sources with the exception of Spain. 3% of the measurement days were characterized by air masses coming from both the Southern Mediterranean Sea and the Africa continent, and the Western Mediterranean, the Iberian Peninsula, and the Atlantic Ocean. 62% of the measurement days were characterized by mixed advection patterns. We found that AOD, SSA and g average values were not significantly dependent on air mass source regions. In contrast, η and Lr average values were quite affected by the air mass source region. AOD, &eta, SSA, g, and Lr average values, which were equal to 0.29±0.15, 0.93±0.03, 0.93±0.03, 0.67±0.03, and 72±20 sr, respectively indicated that the aerosol advected from all continental European sources with the exception of Spain, could be considered representative of "continental average aerosol", mostly made of water soluble and a small amount of soot and insoluble components. Polluted-desert dust particles characterized by AOD=0.29±0.05, η=0.72±0.05, SSA=0.94±0.03, g=0.69±0.02, Lr=56±13 sr, were advected over south-east Italy from the Southern Mediterranean Sea and the Africa continent. The Western Mediterranean, the Iberian Peninsula, and the Atlantic Ocean were instead responsible of the advection of maritime-polluted particles, which were characterized by AOD=0.27±0.17, η=0.8±0.1, SSA=0.94±0.03, g=0.67±0.03, Lr=58±24 sr. Hence, we found that the aerosol load over south-east Italy was dominated by moderately-absorbing, fine-mode particles even if it was also affected by the minor contribution of desert and maritime type aerosol. The application of an aerosol mask to the data points retrieved on measurement days characterized by mixed advection patterns, supported last comment

Description: The eruption of the Icelandic volcano Eyjafjallajökull in April–May 2010 represents a "natural experiment" to study the impact of volcanic emissions on a continental scale. For the first time, quantitative data about the presence, altitude, and layering of the volcanic cloud, in conjunction with optical information, are available for most parts of Europe derived from the observations by the European Aerosol Research Lidar NETwork (EARLINET). Based on multi-wavelength Raman lidar systems, EARLINET is the only instrument worldwide that is able to provide dense time series of high-quality optical data to be used for aerosol typing and for the retrieval of particle microphysical properties as a function of altitude. In this work we show the four-dimensional (4-D) distribution of the Eyjafjallajökull volcanic cloud in the troposphere over Europe as observed by EARLINET during the entire volcanic event (15 April–26 May 2010). All optical properties directly measured (backscatter, extinction, and particle linear depolarization ratio) are stored in the EARLINET database available at http://www.earlinet.org. A specific relational database providing the volcanic mask over Europe, realized ad hoc for this specific event, has been developed and is available on request at http://www.earlinet.org. During the first days after the eruption, volcanic particles were detected over Central Europe within a wide range of altitudes, from the upper troposphere down to the local planetary boundary layer (PBL). After 19 April 2010, volcanic particles were detected over southern and south-eastern Europe. During the first half of May (5–15 May), material emitted by the Eyjafjallajökull volcano was detected over Spain and Portugal and then over the Mediterranean and the Balkans. The last observations of the event were recorded until 25 May in Central Europe and in the Eastern Mediterranean area. The 4-D distribution of volcanic aerosol layering and optical properties on European scale reported here provides an unprecedented data set for evaluating satellite data and aerosol dispersion models for this kind of volcanic events.

Description: The paper investigates numerical procedures that allow determining the dependence on altitude of aerosol properties from multi wavelength elastic lidar signals. In particular, the potential of the LIdar/Radiometer Inversion Code (LIRIC) to retrieve the vertical profiles of fine and coarse-mode particles by combining 3-wavelength lidar measurements and collocated AERONET (AErosol RObotic NETwork) sun/sky photometer measurements is investigated. The used lidar signals are at 355, 532 and 1064 nm. Aerosol extinction coefficient (αL), lidar ratio (LRL), and Ångstrom exponent (ÅL) profiles from LIRIC are compared with the corresponding profiles (α, LR, and Å) retrieved from a Constrained Iterative Inversion (CII) procedure to investigate the LIRIC retrieval ability. Then, an aerosol classification framework which relies on the use of a graphical framework and on the combined analysis of the Ångstrom exponent (at the 355 and 1064 nm wavelength pair, Å(355, 1064)) and its spectral curvature (ΔÅ = Å(355, 532)–Å(532, 1064)) is used to investigate the ability of LIRIC to retrieve vertical profiles of fine and coarse-mode particles. The Å-ΔÅ aerosol classification framework allows estimating the dependence on altitude of the aerosol fine modal radius and of the fine mode contribution to the whole aerosol optical thickness, as discussed in Perrone et al. (2014). The application of LIRIC to three different aerosol scenarios dealing with aerosol properties dependent on altitude has revealed that the differences between αL and α vary with the altitude and on average increase with the decrease of the lidar signal wavelength. It has also been found that the differences between ÅL and corresponding Å values vary with the altitude and the wavelength pair. The sensitivity of Ångstrom exponents to the aerosol size distribution which vary with the wavelength pair was responsible for these last results. The aerosol classification framework has revealed that the deviations between LIRIC and the corresponding CII-procedure retrieval products are due to the fact that LIRIC does not allow to the modal radius of fine mode particles to vary with the altitude. It is shown that this represents the main source of uncertainties in LIRIC results. The plot on the graphical framework of the Å-ΔÅ data points retrieved from the CII-procedure has indicated that the fine-mode-particle modal radius can vary with altitude when particles from different sources and/or from different advection routes contribute to the aerosol load. Analytical back trajectories combined with linear particle depolarization ratio profiles from lidar measurements at 355 nm and dust concentrations from the Barcelona Supercomputing Center-Dust REgional Atmospheric Model (BSC-DREAM) have been used to demonstrate the dependence on altitude of the aerosol properties.

Description: The all-sky direct radiative effect by anthropogenic aerosol (DREa) is calculated in the solar (0.3–4 μm) and infrared (4–200 μm) spectral ranges for six Mediterranean sites. The sites are differently affected by pollution and together reflect typical aerosol impacts that are expected over land and coastal sites of the central Mediterranean basin. Central to the simulations are aerosol optical properties from AERONET sun-/sky-photometer statistics for the year 2003. A discussion on the variability of the overall (natural + anthropogenic) aerosol properties with site location is provided. Supplementary data include MODIS satellite sensor based solar surface albedos, ISCCP products for high- mid- and low cloud cover and estimates for the anthropogenic aerosol fraction from global aerosol models. Since anthropogenic aerosol particles are considered to be smaller than 1 μm in size, mainly the solar radiation transfer is affected with impacts only during sun-light hours. At all sites the (daily average) solar DREa is negative all year round at the top of the atmosphere (ToA). Hence, anthropogenic particles produce over coastal and land sites of the central Mediterranean a significant cooling effect. Monthly DREa values vary from site to site and are seasonally dependent as a consequence of the seasonal dependence of available sun-light and microphysical aerosol properties. At the ToA the monthly average DREa is −(4±1) W m−2 during spring-summer (SS, April–September) and −(2±1) W m−2 during autumn-winter (AW, October–March) at the polluted sites. In contrast, it varies between −(3±1) W m−2 and −(1±1) W m−2 on SS and AW, respectively at the less polluted site. Due to atmospheric absorption the DREa at the surface is larger than at the ToA. At the surface the monthly average DREa varies between the most and the least polluted site between −(7±1) W m−2 and −(4±1) W m−2 during SS, and between −(4±3) W m−2 and −(1±1) W m−2 during AW. The DREa at infrared wavelengths is positive but negligible, especially at the ToA (

Description: The regional climate model RegCM3 coupled with a radiatively active aerosol model with online feedback is used to investigate direct and semi-direct radiative aerosol effects over the Sahara and Europe in a test case of July 2003. The aerosol model includes dust particles in addition to sulfates, hydrophobic and hydrophilic black carbon and organic carbon. The role of the aerosol online feedback on the radiation budget and the direct radiative forcing (short-wave and long-wave) by dust particles are investigated by intercomparing results from three experiments: REF, including all interactive aerosol components, Exp1, not accounting for the aerosol radiative feedback, and Exp2 not accounting for desert dust particles. The comparison of results in the REF experiment with satellite observations, sun/sky radiometer measurements, and lidar profiles at selected Central Mediterranean sites reveals that the spatio-temporal evolution of the aerosol optical depth is reasonably well reproduced by the model during the entire month of July. Results for the dust outbreaks of 17 and 24 July, averaged over the simulation domain, show that the daily-mean SW direct radiative forcing by all particles is −24 Wm−2 and −3.4 Wm−2 on 17 July and −25 Wm−2 and −3.5 Wm−2 on 24 July at the surface and top of the atmosphere, respectively. This is partially offset by the LW direct radiative forcing, which is 7.6 Wm−2 and 1.9 Wm−2 on 17 July and 8.4 Wm−2 and 1.9 Wm−2 on 24 July at the surface and top of the atmosphere, respectively. Hence, the daily-mean SW forcing is offset by the LW forcing of ~30% at the surface and of ~50% at the ToA. It is also shown that atmospheric dynamics and hence dust production and advection processes are dependent on the simulation assumptions and may significantly change within few tens of kilometers. The comparison of REF and Exp1 shows that the aerosol online feedback on the radiation budget decreases the domain-average daily-mean value of the 2 m-temperature, aerosol column burden (CB), and short-wave (SW) atmospheric forcing by −0.52 °C, 14%, and 0.9%, respectively on 17 July and by −0.39 °C, 12% and 12%, respectively on 24 July. The comparison of REF and Exp2 reveals that on 17 July, radiatively-active dust particles decrease the daily-mean 2 m-temperature averaged over the whole simulation domain by 0.4% even if are responsible for 99.8% and 97% of the daily-mean aerosol column burden and SW atmospheric forcing, respectively.

Description: Dust samples from rainfall residues have been collected in southeast Italy (40º 20' N, 18º 6' E) during dust outbreaks occurred from April to June 2002 to characterize morphological and elemental particle composition by different techniques, and investigate the dependence of particle properties on source regions. Four-day analytical back trajectories and satellite images have been used to infer source regions of the investigated dust samples. It has been found that the TOMS absorbing aerosol index was in the range 0.7-2.2 over Southern Italy when samples have been collected. The particle-size and -shape analysis by a scanning electron microscope (SEM) has revealed either that the particle-diameter distribution was between 0.3 and 30 mm with median-diameter values between 1.7-2.4 mm, and that the particles were characterized by a roundness factor varying from 0.8 to 2.5. The infrared transmission spectra have allowed recognizing that all dust samples contained a significant amount of illite. The X-ray energy dispersive (EDX) measurements have revealed that the Al/Si ratio of the transported dust varies from 0.41 to 0.50, and that the Al/Si, Ca/Al, K/Ca, and Fe/Ca ratios differ according to source regions and therefore can be used as indicators of dust source regions. Indeed, it has been found that dust samples with larger Ca/Al and Si/Al ratios and lower Fe/Ca and K/Ca ratios, have been collected along dust events with a source region in northwestern Sahara. On the contrary, the samples collected along dust events with the origin mainly in Chad, Niger, Algeria and Lybia were characterized by larger Fe/Ca and K/Ca ratios.

Description: We compare ground-based measurements of aerosol optical depth and Ångström parameter at six Arctic stations in the period 2001–2006 with the results from two global aerosol dynamics and transport models, ECHAM-HAM and TM5. Satellite measurements from MODIS and the MACC reanalysis product are used to examine the spatial distribution and the seasonality of these parameters and to compare them with model results. We find that both models provide a good reproduction of the Ångström parameter but significantly underestimate the observed AOD values. We also explore the effects of changes in emissions, model resolution and the parametrization of wet scavenging.

Description: The eruption of the Icelandic volcano Eyjafjallajökull in April/May 2010 represents a "natural experiment" to study the impact of volcanic emissions on a continental scale. For the first time, quantitative data about the presence, altitude, and layering of the volcanic cloud, in conjunction with optical information, are available for most parts of Europe derived from the observations by the European Aerosol Research Lidar NETwork (EARLINET). Based on multi-wavelength Raman lidar systems EARLINET is the only instrument worldwide that is able to provide dense time series of high-quality optical data to be used for aerosol typing and for the retrieval of particle microphysical properties as a function of altitude. In this work we show the four-dimensional (4-D) distribution of the Eyjafjallajökull volcanic cloud over Europe as observed by EARLINET during the entire volcanic event (15 April–26 May 2010). All optical properties directly measured (backscatter, extinction, and particle linear depolarization ratio) are stored in the EARLINET database available at http://www.earlinet.org. A specific relational database providing the volcanic mask over Europe, realized ad hoc for this specific event, has been developed and is available on request at http://www.earlinet.org. During the first days after the eruption, volcanic particles were detected over Central Europe within a wide range of altitudes, from the lower stratosphere down to the local Planetary Boundary Layer (PBL). After 19 April 2010, volcanic particles were detected over South and South Eastern Europe. During the first half of May (5–15 May), material emitted by the Eyjafjallajökull volcano was detected over Spain and Portugal and then over the Mediterranean and the Balkans. Last observations of the event were recorded until 25 May in Central Europe and in the Eastern Mediterranean area. For the first time, volcanic aerosol layering and optical properties are presented and discussed for the entire volcanic event on a continental scale providing an unprecedented data set for evaluating satellite data and aerosol dispersion models for these kind of volcanic events.