ALBERT

Description: The Castrovillari scarps (Cfs) are located in northern Calabria (Italy) and consist of three main WSW-dipping fault scarps resulting from multiple rupture events. At the surface, these scarps are defined by multiple breaks in slope. Despite its near-surface complexity, the faults likely merge to form a single normal fault at about 200 m depth, which we refer to as the Castrovillari fault. We present the results of a multidisciplinary and multiscale study at a selected site of the Cfs with the aim to (i) characterize the geometry at the surface and at depth and (ii) obtain constraints on the fault slip history. We investigate the site by merging data from quantitative geomorphological analyses, electrical resistivity and ground penetrating radar surveys, and palaeoseismological trenching along a ~40 m high scarp. The closely spaced investigations allow us to reconstruct the shallow stratigraphy, define the fault locations, and measure the faulted stratigraphic offsets down to 20 m depth. Despite the varying resolutions, each of the adopted approaches suggests the presence of sub-parallel fault planes below the scarps at approximately the same location. The merged datasets permit the evaluation of the fault array (along strike for 220 m within a 370-m-wide zone). The main fault zone consists of two closely spaced NW–SE striking fault planes in the upper portion of the scarp slope and another fault at the scarp foot. The 3-D image of the fault surfaces shows west to southwest dipping planes with values between 70° and 80°; the two closely spaced planes join at about 200 m below the surface. The 8-to-12-m-high upper fault, which shows the higher vertical displacements, accommodated most of the deformation during the Holocene. Results from the trenching analysis indicate a minimum slip per event of 0.6 m and a maximum short-term slip rate of 0.6 mm yr –1 for the Cf. The shallow subsurface imaging techniques are particularly helpful in evaluating the possible field uncertainties related to postfaulting modification by erosional/depositional/human processes, such as within stream valleys and urbanized zones.

Description: Geodetic, geologic and palaeomagnetic data reveal that Oregon (western USA) rotates clockwise at 0.3 to 1.0° Ma –1 (relative to North America) about an axis near the Idaho–Oregon–Washington border, while northeast Washington is relatively fixed. This rotation has been going on for at least 15 Ma. The Yakima fold and thrust belt (YFTB) forms the boundary between northern Oregon and central Washington where convergence of the clockwise-rotating Oregon block is apparently accommodated. North–south shortening across the YFTB has been thought to occur in a fan-like manner, increasing in rate to the west. We obtained high-accuracy, high-density geodetic GPS measurements in 2012–2014 that are used with earlier GPS measurements from the 1990s to characterize YFTB kinematics. The new results show that the deformation associated with the YFTB starts at the Blue Mountains Anticline in northern Oregon and extends north beyond the Frenchman Hills in Washington, past the epicentre of the 1872 M w 7.0 Entiat earthquake to 49°N. The north–south strain rate across the region is 2 to 3 x 10 –9 yr –1 between the volcanic arc and the eastern edge of the YFTB (241.0°E); east of there it drops to about 10 –9 yr –1 . At the eastern boundary of the YFTB, faults and earthquake activity are truncated by a north-trending, narrow zone of deformation that runs along the Pasco Basin and Moses Lake regions near 240.9°E. This zone, abutting the Department of Energy Hanford Nuclear Reservation, accommodates about 0.5 mm yr –1 of east to northeast shortening. A similar zone of N-trending transpression is seen along 239.9°E where there is a change in the strike of the Yakima folds. The modern deformation of the YFTB is about 600 km wide from south to north and internally may be controlled by pre-existing crustal structure.

Description: Geodynamic models predict that rifting of thick, ancient continental lithosphere should not occur unless it is weakened by heating and magmatic intrusion. Therefore, the processes occurring along sections of the western branch of the East African Rift, where ~150 km thick, Palaeoproterozoic lithosphere is rifting with no surface expression of magmatism, are a significant challenge to understand. In an attempt to understand the apparently amagmatic extension we probed the regional uppermost mantle for signatures of thermal alteration using compressional ( Vp ) and shear ( Vs ) wave speeds derived from Pn and Sn tomography. Pervasive thermal alteration of the uppermost mantle and possibly the presence of melt can be inferred beneath the Rungwe volcanic centre, but no signatures on a similar scale were discerned beneath amagmatic portions of the western rift branch encompassing the southern half of the Lake Tanganyika rift and much of the Rukwa rift. In this region, Vp and Vs wave speeds indicate little, if any, heating of the uppermost mantle and no studies have reported dyking. Vp / Vs ratios are consistent with typical, melt-free, olivine-dominated upper mantle. Although our resolution limit precludes us from imaging potential localised magmatic intrusions with dimensions of tens of kilometres, the absence of surface volcanism, the amagmatic upper crustal rupture known to have occurred at disparate locations on the western branch, the presence of lower crustal seismicity and the low temperatures implied by the fast seismic wave speeds in the lower crust and uppermost mantle in this region suggests possible amagmatic extension. Most dynamic models predict that this should not happen. Indeed even with magmatic intrusion, rifting of continental lithosphere 〉100 km thick is considered improbable under conditions found on Earth. Yield strength envelopes confirm that currently modelled stresses are insufficient to produce the observed deformation along these portions of the rift system. Stresses arising from the gravitational force related to the uplift of the East African Plateau provide only one-eighth of the minimum stress necessary to produce observed lower crustal earthquakes in the western branch. We expect that some of this disparity may be accounted for by considering smaller scale bending stresses and dynamic feedbacks between brittle and elastic deformation and between faulting, topography and weathering that are not currently included in models of the East African Rift.

Description: The 2011 October 23 M W 7.1 Van earthquake in eastern Turkey caused ~600 deaths and caused widespread damage and economic loss. The seismogenic rupture was restricted to 10–25 km in depth, but aseismic surface creep, coincident with outcrop fault exposures, was observed in the hours to months after the earthquake. We combine observations from radar interferometry, seismology, geomorphology and Quaternary dating to investigate the geological slip rate and seismotectonic context of the Van earthquake, and assess the implications for continuing seismic hazard in the region. Transient post-seismic slip on the upper Van fault started immediately following the earthquake, and decayed over a period of weeks; it may not fully account for our long-term surface slip-rate estimate of ≥0.5 mm yr –1 . Post-seismic slip on the Bostanici splay fault initiated several days to weeks after the main shock, and we infer that it may have followed the M W  5.9 aftershock on the 9th November. The Van earthquake shows that updip segmentation can be important in arresting seismic ruptures on dip-slip faults. Two large, shallow aftershocks show that the upper 10 km of crust can sustain significant earthquakes, and significant slip is observed to have reached the surface in the late Quaternary, so there may be a continuing seismic hazard from the upper Van fault and the associated splay. The wavelength of folding in the hanging wall of the Van fault is dominated by the structure in the upper 10 km of the crust, masking the effect of deeper seismogenic structures. Thus, models of subsurface faulting based solely on surface folding and faulting in regions of reverse faulting may underestimate the full depth extent of seismogenic structures in the region. In measuring the cumulative post-seismic offsets to anthropogenic structures, we show that Structure-from-Motion can be rapidly deployed to create snapshots of post-seismic displacement. We also demonstrate the utility of declassified Corona mission imagery (1960s–1970s) for geomorphic mapping in areas where recent urbanization has concealed the geomorphic markers.

Description: Volcanic crises are often preceded and accompanied by volcano deformation caused by magmatic and hydrothermal processes. Fast and efficient model identification and parameter estimation techniques for various sources of deformation are crucial for process understanding, volcano hazard assessment and early warning purposes. As a simple model that can be a basis for rapid inversion techniques, we present a compound dislocation model (CDM) that is composed of three mutually orthogonal rectangular dislocations (RDs). We present new RD solutions, which are free of artefact singularities and that also possess full rotational degrees of freedom. The CDM can represent both planar intrusions in the near field and volumetric sources of inflation and deflation in the far field. Therefore, this source model can be applied to shallow dikes and sills, as well as to deep planar and equidimensional sources of any geometry, including oblate, prolate and other triaxial ellipsoidal shapes. In either case the sources may possess any arbitrary orientation in space. After systematically evaluating the CDM, we apply it to the co-eruptive displacements of the 2015 Calbuco eruption observed by the Sentinel-1A satellite in both ascending and descending orbits. The results show that the deformation source is a deflating vertical lens-shaped source at an approximate depth of 8 km centred beneath Calbuco volcano. The parameters of the optimal source model clearly show that it is significantly different from an isotropic point source or a single dislocation model. The Calbuco example reflects the convenience of using the CDM for a rapid interpretation of deformation data.

Description: Tehran, the capital city of Iran with a population of over 12 million, is one of the largest urban centres within the seismically active Alpine–Himalayan orogenic belt. Although several historic earthquakes have affected Tehran, their relation to individual faults is ambiguous for most. This ambiguity is partly due to a lack of knowledge about the locations, geometries and seismic potential of structures that have been obscured by dramatic urban growth over the past three decades, and which have covered most of the young geomorphic markers and natural exposures. Here we use aerial photographs from 1956, combined with an ~1 m DEM derived from stereo Pleiades satellite imagery to investigate the geomorphology of a growing anticline above a thrust fault—the Pardisan thrust—within central Tehran. The topography across the ridge is consistent with a steep ramp extending from close to the surface to a depth of ~2 km, where it presumably connects with a shallow-dipping detachment. No primary fault is visible at the surface, and it is possible that the faulting dissipates in the near surface as distributed shearing. We use optically stimulated luminescence to date remnants of uplifted and warped alluvial deposits that are offset vertically across the Pardisan fault, providing minimum uplift and slip-rates of at least 1 mm yr –1 . Our study shows that the faults within the Tehran urban region have relatively rapid rates of slip, are important in the regional tectonics, and have a great impact on earthquake hazard assessment of the city and surrounding region.

Description: Geophysical data from the MEDOC experiment across the Northern Tyrrhenian backarc basin has mapped a failed rift during backarc extension of cratonic Variscan lithosphere. In contrast, data across the Central Tyrrhenian have revealed the presence of magmatic accretion followed by mantle exhumation after continental breakup. Here we analyse the MEDOC transect E–F, which extends from Sardinia to the Campania margin at 40.5°N, to define the distribution of geological domains in the transition from the complex Central Tyrrhenian to the extended continental crust of the Northern Tyrrhenian. The crust and uppermost mantle structure along this ~400-km-long transect have been investigated based on wide-angle seismic data, gravity modelling and multichannel seismic reflection imaging. The P -wave tomographic model together with a P -wave-velocity-derived density model and the multichannel seismic images reveal seven different domains along this transect, in contrast to the simpler structure to the south and north. The stretched continental crust under Sardinia margin abuts the magmatic crust of Cornaglia Terrace, where accretion likely occurred during backarc extension. Eastwards, around Secchi seamount, a second segment of thinned continental crust (7–8 km) is observed. Two short segments of magmatically modified continental crust are separated by the ~5-km-wide segment of the Vavilov basin possibly made of exhumed mantle rocks. The eastern segment of the 40.5°N transect E–F is characterized by continental crust extending from mainland Italy towards the Campania margin. Ground truthing and prior geophysical information obtained north and south of transect E–F was integrated in this study to map the spatial distribution of basement domains in the Central Tyrrhenian basin. The northward transition of crustal domains depicts a complex 3-D structure represented by abrupt spatial changes of magmatic and non-magmatic crustal domains. These observations imply rapid variations of magmatic activity difficult to reconcile with current models of extension of continental lithosphere essentially 2-D over long distances.

Description: Three 2-D Deep Electrical Resistivity Tomography (ERT) transects, up to 6.36 km long, were obtained across the Paganica-San Demetrio Basin, bounded by the 2009 L'Aquila M w 6.1 normal-faulting earthquake causative fault (central Italy). The investigations allowed defining for the first time the shallow subsurface basin structure. The resistivity images, and their geological interpretation, show a dissected Mesozoic-Tertiary substratum buried under continental infill of mainly Quaternary age due to the long-term activity of the Paganica-San Demetrio normal faults system (PSDFS), ruling the most recent deformational phase. Our results indicate that the basin bottom deepens up to 600 m moving to the south, with the continental infill largely exceeding the known thickness of the Quaternary sequence. The causes of this increasing thickness can be: (1) the onset of the continental deposition in the southern sector took place before the Quaternary, (2) there was an early stage of the basin development driven by different fault systems that produced a depocentre in the southern sector not related to the present-day basin shape, or (3) the fault system slip rate in the southern sector was faster than in the northern sector. We were able to gain sights into the long-term PSDFS behaviour and evolution, by comparing throw rates at different timescales and discriminating the splays that lead deformation. Some fault splays exhibit large cumulative throws (〉300 m) in coincidence with large displacement of the continental deposits sequence (〉100 m), thus testifying a general persistence in time of their activity as leading splays of the fault system. We evaluate the long-term (3–2.5 Myr) cumulative and Quaternary throw rates of most of the leading splays to be 0.08–0.17 mm yr –1 , indicating a substantial stability of the faults activity. Among them, an individual leading fault splay extends from Paganica to San Demetrio ne’ Vestini as a result of a post-Early Pleistocene linkage of two smaller splays. This 15 km long fault splay can explain the Holocene surface ruptures observed to be larger than those occurred during the 2009 L'Aquila earthquake, such as revealed by palaeoseismological investigations. Finally, the architecture of the basin at depth suggests that the PSDFS can also rupture a longer structure at the surface, allowing earthquakes larger than M 6.5, besides rupturing only small sections, as it occurred in 2009.

Description: The normal fault-system responsible of the 2009 M w 6.1 L'Aquila earthquake (Paganica-San Demetrio fault-system) comprises several narrow, fault-parallel valleys of controversial origin. We investigated a key section of the southeastern portion of this fault network along the small Verupola Valley. In order to characterize its nature and possible tectonic activity, we applied multiple-geosciences techniques able to image at depth the structure associated to this peculiar landform. We integrated magnetometry, 2-D P wave and resistivity tomography, surface waves and seismic noise analysis coupled with field mapping, shallow boreholes and trenching. According to our results, the Verupola Valley is a ~30–40-m-deep graben controlled by a SW-dipping master fault and synthetic splays paired with an antithetic NE-dipping fault. The SW-dipping splays are active and cut very shallow (〈2 m deep) Late Pleistocene sediments. The small amount of cumulated vertical offset (~15 m) across the conjugated system may indicate a young fault inception or very low Quaternary slip-rates. Due to its structural continuity with the adjacent mapped strands of the Paganica–San Demetrio fault network, we relate the Verupola Valley to the recent activity of the southeastern segment of this fault system. We also suggest that other fault-parallel valleys can have the same tectonic origin and setting of the Verupola Valley. This latter represents a scale-independent analogue from metric scale (exposed in the palaeoseismological trenches) to the Middle Aterno Basin scale (seen from seismic profiles and fault mapping). Overall, the imaged structural style is coherent with the regional tectonic setting due to Quaternary crustal extension.

Description: The Taupo Volcanic Zone (TVZ) is one of the world's most productive regions of rhyolitic volcanism and contains the highly active Okataina Volcanic Centre (OVC). Within the TVZ, intra-arc extension is expressed as normal faulting within a zone known as the Taupo Rift. The OVC is located within a complex part of the rift, where volcanism and deformation is considered influenced by rift structure and kinematics. There has been significant research on the structural, volcanic and geophysical properties of the rift and OVC, but less focus on deformation using geodetic data. The limited studies that have utilized geodetic data do not clearly resolve the distribution of deformation and strain rates within the rift and OVC. This is essential to ensure that deformation signals from volcanic processes at the OVC are correctly identified and distinguished from those related to regional tectonic or local hydrothermal processes within the rift. In this paper, we present a picture of contemporary deformation at the OVC and within the surrounding rift in detail, using existing and new GPS campaign and continuous GPS (cGPS) data collected between 1998 and 2011. The results show a highly heterogeneous deformation and strain rate field (both extension and shortening) through the study area, partitioned into different parts of the rift. Our results agree well with earlier geodetic studies, as well as identify new features, but some deformation patterns conflict with long-term geological observations. In the OVC, we observe a locally rotated horizontal velocity field, significant vertical deformation and variable strain rates across the caldera. In the Tarawera Rift, we identify elevated extension and shear rates, which may have significant implications for volcanism there. A shortening pattern is identified through the central rift, which is unexpected in an intra-arc rifting environment. We attempt to explain the source/s of shortening and extension and discuss their implications for geodetic monitoring efforts in the OVC.