ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Articles  (52)
  • Physics  (52)
  • 2020-2023
  • 2010-2014
  • 1970-1974
  • 1965-1969  (52)
  • 1960-1964
  • 1945-1949
  • 1935-1939
  • 1968  (52)
  • 1
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 1183-1202 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Crosslinked samples of polyethylene were prepared by electron irradiation of both high- and low-density polymers in the crystalline state. A further crosslinked sample was obtained by curing a high-density polyethylene by reaction with dicumyl peroxide at 180°C. The stress-strain-birefringenece relations were obtained on specimens cut from these samples at temperatures between 130 and 250°C. All samples showed a substantial decrease in stress-optical coefficient with increasing degree of crosslinking and with increasing temperature. The stress-optical properties at each temperature were extrapolated to zero degree of crosslinking to give quantities characteristic of the Gaussian network. Comparison of these properties with the theory of networks of rotational isomeric chains with both independent and interdependent rotation allows estimates to be obtained for (1) the trans-gauche energy differences in rotation around skeletal bonds and (2) the difference in principal optical polarizabilities for the CH2 group in the elastomeric state. This latter quantity is shown to be more nearly given by Denbigh's than by Bunn and Daubeny's bond polarizability values.
    Additional Material: 7 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-1: Polymer Chemistry 6 (1968), S. 2001-2012 
    ISSN: 0449-296X
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology
    Notes: Emulsion polymerization of methacrolein produces a polyacetal which can be converted through the action of sodium hydroxide to an alternating copolymer of methallyl alcohol and sodium methacrylate. Support for the alternating structure was gained primarily through a study of the polylactone formed through subsequent acidification of the sodium salt. Thus, the poly(methallyl alcohol-sodium methacrylate) copolymer was acidified under selected conditions to give a soluble polylactone containing 14.2 mole-% of residual acid and hydroxyl groups. This number agrees quite closely with the value of 13.5 mole-% which one would predict from the random cyclization of a true alternating copolymer. Cyclization of a random copolymer of poly(methallyl alcohol-sodium methacrylate) in a random fashion would have resulted in a value of about 36.8 mole-%. The results also support both the 1,2 vinyl polymerization of methacrolein and a nonrandom attack of the polymethacrolein by base. In a completely separate set of experiments, the value of r1 and r2 for the copolymerization of styrene (M1) and methacrolein (M2) were determined to be 0.22 ± 0.02 and 0.88 ± 0.02, respectively.
    Additional Material: 6 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 3
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 463-477 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: The conductivity of dry poly(hexamethylene adipamide) (nylon 66) was measured as a function of time and temperature. Three temperature ranges were observed in which the time dependence of conductivity differed: (a) below 80°C. the conductivity decreased continuously with time; (b) between 80°C. and 110°C. the conductivity remained constant over long periods; (c) above 120°C. a continuous decrease in conductivity was again observed. In other experiments the volume of gas evolved from the nylon film was measured under continuous potential and compared with the total current passed through the sample. It was observed that above 120°C. the gas evolved corresponded to about one-half the volume calculated if the conduction process involved only protons. Below 120°C. the gas evolved corresponded to an increasingly small fraction of the total current until below 90°C. no evolution of gas was observed. This suggests that at temperatures above 120°C. conduction involves the transport of both protons and electrons, whereas at lower temperatures it is electronic. Mechanisms of conduction are discussed.
    Additional Material: 7 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 4
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 1689-1703 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Stress-induced crystallization in a rapidly stretched natural rubber gum vulcanizate has been studied using thermal techniques to follow the development of crystallinity. A special-purpose analog computer has been assembled and used on-line to process the thermal and mechanical data obtained in high speed tensile testing. Roughly first-order room temperature crystallization kinetics curves were obtained having time constants of 50-60 msec in the range of 400-540% extension. While the rate of this rapid, presumably primary crystallization appears rather insensitive to elongation in this limited range, the extent of crystallization at 400 msec increases smoothly from zero at 340% elongation to around 18% at 540% elongation. It is shown that our high-speed tensile tester can stretch this vulcanizate fast enough that most of the crystallization takes place after extension has been completed. Stress-strain curves obtained at this high rate are compared with those obtained at lower rates where crystallization takes place during the stretching.
    Additional Material: 9 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 5
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 1209-1216 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: It is predicted that the net repulsion between the segments of a polymer network and a poor solvent can cause a phase transition marked by a sudden change in the degree of swelling. This is analogous to the “coil-globule” transition recently predicted by Ptitsyn to occur for a macromolecule in solution. The critical conditions for the transition. as well as phase diagrams, are calculated for the gel in free swelling and under uniaxial tension, which facilitates the transition. The transition depends on the gel being formed of chains crosslinked while greatly swollen by a diluent and also having a high degree of crosslinking. It is concluded that it would be difficult to attain the conditions necessary for the transition in the free-swelling case, but that it should be possible for gel under tension.
    Additional Material: 5 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 6
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 967-980 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Viscoelastic properties of uncrosslinked 1,2-polybutadiene (91.5% vinyl, 7.0% cis, 1.5% trans, number-average molecular weight 99,000) were studied by dynamic shear measurements between 0.15 and 600 cps (torsion pendulum and Fitzgerald transducer) and shear creep measurements over time periods up to 3.7 × 104 sec., in the temperature rang from 5 to 50°C. More limited dynamic measurements were made on a sample of unvulcanized natural rubber with number-average molecular weight 350,000 at frequencies from 0.4 to 400 cps and temperatures from 13 to 48°C. All data were reduced to 25°C. by shift factors calculated from equations of the WLF form with the following coefficients: 1,2-polybutadiene, c1 = 6.23, c2 = 72.5; natural rubber, c1 = 5.94, c2 = 151.6. In the transition zone, the relative positions of the loss tangent curves on the logarithmic frequency scale for these and other rubbers (1,4-polybutadiene with 50% trans configuration; styrene-butadiene rubber with 23.5% styrene content; and polyisobutylene) provided relative measures of local segment mobility. At 25°C., these ranged over a factor of 3700 with 1,2-polybutadiene and polyisobutylene the lowest and 1,4-polybutadiene the highest. When the frequency scale of each rubber was reduced to a temperature 100°C. above its glass transition temperature, however, the loss tangent curves for all except polyisobutylene were nearly coincident; the latter still showed a lower mobility by a factor of about 1/800. The terminal relaxation time and steady-state compliance for the 1,2-polybutadiene calculated from the Rouse theory were larger than those observed experimentally. The level of compliance corresponding to the entanglement network of 1,2-polybutadiene, JeN, was calculated by integration over the loss compliance, J″, to be 1.62 × 10-7 cm.2/dyne; integration over G″ to obtain the corresponding modulus gave reasonable agreement. From such JeN, values, the average number of chain atoms between entanglement points, jZe, was estimated as follows: 1,2-polybutadiene, 132; natural rubber, 360; 1,4-polybutadiene, 110; styrene-butadiene rubber, 186; polyisobutylene, 320. Values of jZe were also estimated from the minimum in the loss tangent and compared with those reported from the molecular weight dependence of viscosity. The three sources were in generally good agreement.
    Additional Material: 8 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 7
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 1945-1952 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: The structure of the polycarbonate chain has been analyzed from the point of view of the spatial configurations it may assume. The carbonate group is certainly planar, and the trans,trans configuration probably is strongly preferred. Rotations about the aryloxygen bonds are subject to symmetric, twofold potentials. It follows that the molecule can be treated as a freely rotating chain consisting of a succession of virtual bonds 7.0 Å in length, joined at angles of ca. 112°. Calculations carried out on this basis yield 〈r2〉0/M = 0.85 Å2/g-mole wt for the unperturbed random coil, in excellent agreement with the experimental results of Berry, Nomura, and Mayhan. The effect of occurrence of some of the carbonate groups in cis, trans configurations is investigated using more elaborate methods.
    Additional Material: 2 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 8
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 241-248 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Polyoctadecene-1, as isolated from a Ziegler-type polymerization, was examined by density and refractive index measurements and by differential thermal analysis. Two main transitions were observed, their sharpness suggesting that they are both first-order. Extraction with n-hexane at 25°C. separated the polymer into two almost equal fractions, each showing essentially one of these transitions. Transition temperatures were compared with those of certain other polymers having long n-alkyl side chains. From this comparison, and from the findings of other workers, it was concluded that the polymer of lower transition temperature is atactic polyoctadecene, in which the side chains only participate in crystallization, whereas the polymer of higher transition temperature is tactic polyoctadecene, in which crystallization involves both the main chain and side chains.
    Additional Material: 5 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 9
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 6 (1968), S. 479-492 
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Viscoelastic properties of four linear and three very lightly crosslinked polybutadienes (microstructure about 50% trans) were studied. Of the latter, two had not reached the gel point, and their molecular weight distributions were determined by sedimentation velocity analysis; the third was crosslinked just past the gel point, with only 32% gel fraction present. The crosslinking agent was sulfur. Complex shear compliances were measured over a frequency range from 0.1 to 1000 cps at temperatures from -70 to 30°C. with a Fitzgerald transducer and a Plazek torsion pendulum; and torsional creep measurements were made over time periods up to about three days. The creep data were converted to the corresponding dynamic viscoelastic functions at very low frequencies by conventional approximation methods. All data were reduced to 25°C. by shift factors calculated from a previously adopted equation of the WLF form. In the transition zone, the viscoelastic properties of linear samples were almost independent of molecular weight. The entanglement spacing, derived from the minimum in the loss tangent and the inflection in the storage compliance, was 130 to 160 chain atoms. The maximum in the retardation spectrum attributable to motions of individual network strands was closely similar to the corresponding maxima for more highly crosslinked vulcanizates previously studied, showing that even in the latter it is associated with entanglement network strands rather than strands between chemical crosslinks. For a linear sample with molecular weight 180,000, the retardation processes disappear at times beyond about 10 sec. at 25°C. With crosslinking short of the gel point (i.e., branching) the slow retardation processes are enormously increased and prolonged to longer times. With further crosslinking through the gel point and beyond, the slow retardation processes decrease progressively in magnitude. Qualitatively, this behavior resembles the sharp maximum in content of highly branched and aggregated molecular species which is predicted at the gel point by crosslinking statistics; but the slow processes (or low-frequency losses) persist farther past the gel point than would be expected on this basis. The steady-state compliances of the linear samples were smaller, but for a sample crosslinked short of the gel point were much larger, than the prediction of the Rouse theory modified for molecular weight distribution.
    Additional Material: 5 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 10
    ISSN: 0449-2978
    Keywords: Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: When cellulose triacetates and some hydrolyzed acetates are boiled in 2.5N hydrochloric acid there is no residue. Under the same conditions cellulose is hydrolyzed, and a residue is obtained with a limiting viscosity that is related to the average length of the cellulose crystallites. These findings are combined to develop a method for studying the progress of acetylation through the amorphous portion of cellulose and into the crystallites, and to investigate the relative reactivities of cellulose I and cellulose II. Acetates were made from cotton and wood cellulose by a “fibrous” (heterogeneous) esterification involving sulfoacetic acid or perchloric acid catalyst in acetic acid-acetic anhydride; the final acetyl contents (10-41%) were attained by stopping the reaction at various points short of the triester (rather than by hydrolyzing a triester). When these acetates were boiled in 2.5N HCI they did not disappear completely, and the residues were cellulose I, indicating that cellulose acetate had been removed. With increasing acetyl the yield of residue decreased, and beyond about 33% acetyl the viscosity and x-ray measurements showed that the length and width of the crystallites decreased. However, when a nonsolvent such as toluene was added to the acetylation medium, the limiting viscosity did not change over the same acetyl range (up to 40%). Samples of varying acetyl values were taken during a regular acetylation of cotton linters in a mixer with sulfuric acid catalyst. X-ray studies of the residues obtained by boiling the acetates in 2.5N HCI revealed the presence of unreacted cellulose I even after 40% acetyl had been reached. This explains why the manufacture of cellulose esters from cellulose I requires complete esterification before they are hydrolyzed to the desired acetyl level. It was shown that there is a distinct difference between the acetylation reactivity of cellulose I and cellulose II. This indicates the importance of avoiding cellulose II formation during the refinement of cellulose for the manufacture of cellulose acetate in a process involving activation with acetic acid.
    Additional Material: 22 Ill.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...