ALBERT

Beschreibung: This paper presents the results of a transient computer simulation that was developed to study phase change energy storage techniques for Space Station Freedom (SSF) solar dynamic (SD) power systems. Such SD systems may be used in future growth SSF configurations. Two solar dynamic options are considered in this paper: Brayton and Rankine. Model elements consist of a single node receiver and concentrator, and takes into account overall heat engine efficiency and power distribution characteristics. The simulation not only computes the energy stored in the receiver phase change material (PCM), but also the amount of the PCM required for various combinations of load demands and power system mission constraints. For a solar dynamic power system in low earth orbit, the amount of stored PCM energy is calculated by balancing the solar energy input and the energy consumed by the loads corrected by an overall system efficiency. The model assumes an average 75 kW SD power system load profile which is connected to user loads via dedicated power distribution channels. The model then calculates the stored energy in the receiver and subsequently estimates the quantity of PCM necessary to meet peaking and contingency requirements. The model can also be used to conduct trade studies on the performance of SD power systems using different storage materials.

Beschreibung: The Solar Space Power Analysis Code, SOSPAC, was developed to examine the solar thermal and photovoltaic power generation options available for a satellite or spacecraft in low earth orbit. SOSPAC is a preliminary systems analysis tool and enables the engineer to compare the areas, weights, and costs of several candidate electric and thermal power systems. The configurations studied include photovoltaic arrays and parabolic dish systems to produce electricity only, and in various combinations to provide both thermal and electric power. SOSPAC has been used for comparison and parametric studies of proposed power systems for the NASA Space Station. The initial requirements are projected to be about 40 kW of electrical power, and a similar amount of thermal power with temperatures above 1000 degrees Centigrade. For objects in low earth orbit, the aerodynamic drag caused by suitably large photovoltaic arrays is very substantial. Smaller parabolic dishes can provide thermal energy at a collection efficiency of about 80%, but at increased cost. SOSPAC allows an analysis of cost and performance factors of five hybrid power generating systems. Input includes electrical and thermal power requirements, sun and shade durations for the satellite, and unit weight and cost for subsystems and components. Performance equations of the five configurations are derived, and the output tabulates total weights of the power plant assemblies, area of the arrays, efficiencies, and costs. SOSPAC is written in FORTRAN IV for batch execution and has been implemented on an IBM PC computer operating under DOS with a central memory requirement of approximately 60K of 8 bit bytes. This program was developed in 1985.

Beschreibung: Slush hydrogen, a mixture of the solid and liquid phases of hydrogen, is a possible source of fuel for the National Aerospace Plane (NASP) Project. Advantages of slush hydrogen over liquid hydrogen include greater heat capacity and greater density. However, practical use of slush hydrogen as a fuel requires systems of lines, valves, etc. which are designed to deliver the fuel in slush form with minimal solid loss as a result of pipe heating or flow friction. Engineers involved with the NASP Project developed FLUSH to calculate the pressure drop and slush hydrogen solid fraction loss for steady-state, one-dimensional flow. FLUSH solves the steady-state, one-dimensional energy equation and the Bernoulli equation for pipe flow. The program performs these calculations for each two-node element--straight pipe length, elbow, valve, fitting, or other part of the piping system--specified by the user. The user provides flow rate, upstream pressure, initial solid hydrogen fraction, element heat leak, and element parameters such as length and diameter. For each element, FLUSH first calculates the pressure drop, then figures the slush solid fraction exiting the element. The code employs GASPLUS routines to calculate thermodynamic properties for the slush hydrogen. FLUSH is written in FORTRAN IV for DEC VAX series computers running VMS. An executable is provided on the tape. The GASPLUS physical properties routines which are required for building the executable are included as one object library on the program media (full source code for GASPLUS is available separately as COSMIC Program Number LEW-15091). FLUSH is available in DEC VAX BACKUP format on a 9-track 1600 BPI magnetic tape (standard media) or on a TK50 tape cartridge. FLUSH was developed in 1989.

Beschreibung: Accurate simulation of nuclear thermal propulsion systems using computational methods will permit reductions in testing and, thus, the time and cost of achieving a flight ready status for systems utilizing this advanced technology. An accurate simulation must maintain a "balance-of-plant" where the required pump work equals the supplied turbine work. This turbopump assembly balancing must be integrated into the overall system analysis models. TPA was developed to balance turbine and pump work using performance maps. It requires the inlet properties, performance maps, and shaft speed. TPA then computes the exit conditions and work terms. The work terms can then be balanced by varying the input shaft speed. The objective of the pump analysis is to determine the propellant state properties at the pump exit and the pump work. The pump analysis algorithm for liquid flow assumes that the shaft speed, the propellant state properties at the pump entrance, the propellant flow rate, the pump entrance and exit areas, as well as performance curves, are all known. The analysis of both the pump pressure rise and pump efficiency curves is required. The objective of the turbine analysis is to determine the propellant state properties at the turbine exit and the turbine work. The turbine analysis algorithm assumes that the shaft speed, the propellant state properties at the turbine entrance, the propellant flow rate, the turbine root mean square blade diameter, the turbine entrance and exit areas, as well as performance curves, are all known. The analysis also requires the turbine flow parameter curve and the turbine total efficiency curve. TPA is written in FORTRAN 77 to be machine independent. The TPA package includes the NBS+_PH2 code, which is also available separately (LEW-15505). TPA has been successfully implemented on a DEC VAX series computer running VMS, a Sun4 series computer running SunOS, and an IBM PC compatible computer running MS-DOS. Lahey F77L3 EM/32 v. 5.01 or higher is required for compilation on an IBM PC compatible computer; however, a PC executable is included on the distribution diskette. The standard distribution medium for this program is one 5.25 inch 360K MS-DOS format diskette. The diskette's contents have been compressed using PKWARE's archiving tools. The utility to unarchive the file, PKUNZIP.EXE, is included. Alternate distribution media and formats are available upon request. TPA was developed in 1993.

Beschreibung: Experimental results are reported for submerged injection pressurization and expulsion tests of a 4.89 cu m liquid hydrogen tank. The pressurant injector was positioned near the bottom of the test vessel to simulate liquid engulfment of the pressurant gas inlet, a condition that may occur in low-gravity conditions. Results indicate a substantial reduction in pressurization efficiency with pressurant gas requirements approximately five times greater than ideal amounts. Consequently, submerged vapor injection should be avoided as a low-gravity autogenous pressurization method whenever possible. The work presented herein validates that pressurant requirements are accurately predicted by a homogeneous thermodynamic model when the submerged injection technique is employed.

Beschreibung: Presented here are results of a test program undertaken to further define the response of the solar dynamic radiator to hypervelocity impact (HVI). Tests were conducted on representative radiator panels (under ambient, nonoperating conditions) over a range of velocity. Target parameters are also varied. Data indicate that analytical penetration predictions are conservative (i.e., pessimistic) for the specific configuration of the solar dynamic radiator. Test results are used to define the solar dynamic radiator reliability with respect to HVI more rigorously than previous studies. Test data, reliability, and survivability results are presented.

Beschreibung: Attention is given to a space-borne engine plume experiment study to fly an experiment which will both verify and quantify the reduced contamination from advanced rhenium-iridium earth-storable bipropellant rockets (hot rockets) and provide a correlation between high-fidelity, in-space measurements and theoretical plume and surface contamination models. The experiment conceptual design is based on survey results from plume and contamination technologists throughout the U.S. With respect to shuttle use, cursory investigations validate Hitchhiker availability and adaptability, adequate remote manipulator system (RMS) articulation and dynamic capability, acceptable RMS attachment capability, adequate power and telemetry capability, and adequate flight altitude and attitude/orbital capability.

Beschreibung: A new procedure, dubbed the Munich Method, has been proposed recently for the modeling of rocket engine performance. The author of the Munich Method claims it to be an extension and improvement of the thermodynamic procedures used to model rocket engines in the NASA-Lewis chemical equilibrium program. An examination of the Munich Method shows that it contains several flaws. If these defects are corrected then the Munich Method will produce results identical to those generated by the NASA-Lewis Code.