ALBERT

Description: © 2009 The Authors. This article is distributed under the terms of the Creative Commons Attribution (3.0) License. The definitive version was published in Sensors 9 (2009): 404-429, doi:10.3390/s90100404.

Description: An instrument has been built to carry out continuous in-situ measurement of small differences in water pressure, conductivity and temperature, in natural surface water and groundwater systems. A low-cost data telemetry system provides data on shore in real time if desired. The immediate purpose of measurements by this device is to continuously infer fluxes of water across the sediment-water interface in a complex estuarine system; however, direct application to assessment of sediment-water fluxes in rivers, lakes, and other systems is also possible. Key objectives of the design include both low cost, and accuracy of the order of ±0.5 mm H2O in measured head difference between the instrument’s two pressure ports. These objectives have been met, although a revision to the design of one component was found to be necessary. Deployments of up to nine months, and wireless range in excess of 300 m have been demonstrated.

Description: The electric power industry sector has become increasingly aware of how counterproductive voltage sag affects distribution network systems (DNS). The voltage sag backfires disastrously at the demand load side and affects equipment in DNS. To settle the voltage sag issue, this paper achieved its primary purpose to mitigate the voltage sag based on integrating a hydrogen fuel cell (HFC) with the DNS using a distribution static synchronous compensator (D-STATCOM) system. Besides, this paper discusses the challenges and opportunities of D-STATCOM in DNS. In this paper, using HFC is well-designed, modeled, and simulated to mitigate the voltage sag in DNS with a positive impact on the environment and an immediate response to the issue of the injection of voltage. Furthermore, this modeling and controller are particularly suitable in terms of cost-effectiveness as well as reliability based on the adaptive network fuzzy inference system (ANFIS), fuzzy logic system (FLC), and proportional–integral (P-I). The effectiveness of the MATLAB simulation is confirmed by implementing the system and carrying out a DNS connection, obtaining efficiencies over 94.5% at three-phase fault for values of injection voltage in HFC D-STATCOM using a P-I controller. Moreover, the HFC D-STATCOM using FLC proved capable of supporting the network by 97.00%. The HFC D-STATCOM based ANFIS proved capable of supporting the network by 98.00% in the DNS.

Description: Gut microbiota, a major contributor to human health, is influenced by physical activity and diet, and displays a functional cross-talk with skeletal muscle. Conversely, few data are available on the impact of hypoactivity, although sedentary lifestyles are widespread and associated with negative health and socio-economic impacts. The study aim was to determine the effect of Dry Immersion (DI), a severe hypoactivity model, on the human gut microbiota composition. Stool samples were collected from 14 healthy men before and after 5 days of DI to determine the gut microbiota taxonomic profiles by 16S metagenomic sequencing in strictly controlled dietary conditions. The α and β diversities indices were unchanged. However, the operational taxonomic units associated with the Clostridiales order and the Lachnospiraceae family, belonging to the Firmicutes phylum, were significantly increased after DI. Propionate, a short-chain fatty acid metabolized by skeletal muscle, was significantly reduced in post-DI stool samples. The finding that intestine bacteria are sensitive to hypoactivity raises questions about their impact and role in chronic sedentary lifestyles.

Description: A simple one-pot approach was developed for the synthesis of furan-2(5H)-one derivative containing indole fragments. This method includes the telescoped multicomponent reaction of indole, 4-methoxyphenylglyoxal, and Meldrum’s acid. The synthetic utility of the prepared furan-2(5H)-one was demonstrated by condensation with 4-methoxybenzaldehyde. The advantages of this method include the employment of readily accessible starting materials, atom economy, process simplicity, and the easy isolation of the target products. The structure of the synthesized furanones was confirmed by 1H and 13C-NMR spectroscopy and high-resolution mass spectrometry with electrospray ionization (ESI-HRMS).

Description: Volcanic ash fall-out represents a serious hazard for air and road traffic. The forecasting models used to predict its time–space evolution require information about the core characteristics of volcanic particles, such as their granulometry. Typically, such information is gained by the spot direct observation of the ash collected at the ground or by using expensive instrumentation. In this paper, a vision-based methodology aimed at the estimation of ash granulometry is presented. A dedicated image processing paradigm was developed and implemented in LabVIEW™. The methodology was validated experimentally using digital reference images resembling different operating conditions. The outcome of the assessment procedure was very encouraging, showing an accuracy of the image processing algorithm of 1.76%.

Description: Horizontal wells can significantly improve the gas production and are expected to be an efficient exploitation method for the industrialization of natural gas hydrates (NGHs) in the future. However, the near-wellbore hydrate is highly prone to decomposition during the drilling process, owing to the disturbance aroused by the factors such as the drilling fluid temperature, pressure, and salinity. These issues can result in the engineering accidents such as bit sticking and wellbore instability, which are required for further investigations. This paper studies the characteristics of drilling fluid invasion into the marine NGH reservoir with varied drilling fluid parameters via numerical simulation. The effects of the drilling fluid parameters on the decomposition behavior of near-wellbore hydrates are presented. The simulating results show that the adjustments of drilling fluid density within the mud safety window have limited effects on the NGH decomposition, meanwhile the hydrates reservoir is most sensitive to the drilling fluid temperature variation. If the drilling fluid temperature grows considerably due to improper control, the range of the hydrates decomposition around the horizontal well tends to expand, which then aggravates wellbore instability. When the drilling fluid salinity varies in the range of 3.5–7.5%, the increase in the ion concentration speeds up the hydrate decomposition, which is adverse to maintaining wellbore stability.

Description: Fault tolerance in IoT systems is challenging to overcome due to its complexity, dynamicity, and heterogeneity. IoT systems are typically designed and constructed in layers. Every layer has its requirements and fault tolerance strategies. However, errors in one layer can propagate and cause effects on others. Thus, it is impractical to consider a centralized fault tolerance approach for an entire system. Consequently, it is vital to consider multiple layers in order to enable collaboration and information exchange when addressing fault tolerance. The purpose of this study is to propose a multi-layer fault tolerance approach, granting interconnection among IoT system layers, allowing information exchange and collaboration in order to attain the property of dependability. Therefore, we define an event-driven framework called FaTEMa (Fault Tolerance Event Manager) that creates a dedicated fault-related communication channel in order to propagate events across the levels of the system. The implemented framework assist with error detection and continued service. Additionally, it offers extension points to support heterogeneous communication protocols and evolve new capabilities. Our empirical results show that introducing FaTEMa provided improvements to the error detection and error resolution time, consequently improving system availability. In addition, the use of Fatema provided a reliability improvement and a reduction in the number of failures produced.

Description: Stand structure and topography are important factors affecting forest vegetation carbon density (FVCD). Revealing the interaction mechanisms between stand structure and topography on FVCD is of great significance for enhancing forest vegetation carbon storage and achieving regional carbon neutrality. Based on stratified sampling, systematic distribution and forest continuous inventory sample plots in Jiangxi province, the variation characteristics of FVCD and its correlations with stand structure and topographic factors were studied. The results are as follows: (1) The average FVCD in Jiangxi province was 44.23 Mg/ha, which was dominated by the carbon density of the arbor layer, accounting for about 81.39% of the total forest—far lower than the average level of global FVCD, which proved that the forest in Jiangxi province was dominated by middle-age and young forests with low carbon density, and also showed that the potential for forest vegetation carbon storage in Jiangxi province was huge. (2) Except for vegetation carbon densities of shrub and herb layers, the vegetation carbon densities of other forest layers in Jiangxi province were significantly different among different forest types. Volume per unit area was the most important factor affecting the vegetation carbon densities of arbor and total forest, and vegetation carbon density–volume models of the main forests were built for vegetation carbon density calculation in Jiangxi province. (3) The vegetation carbon densities of arbor layer, snag and log layer, and total forest increased significantly with increases in elevation and slope. Except for the shrub layer and herb layer, the vegetation carbon densities of the other layers and the total forest had extremely significant or significant differences between slope position gradients—indicating that the effect of topography on FVCD in Jiangxi province was significant, mainly through influencing of forest distribution and human disturbance intensity.

Description: This study presents a 2-D lidar odometry based on an ICP (iterative closest point) variant used in a simple and straightforward platform that achieves real-time and low-drift performance. With a designated multi-scale feature extraction procedure, the lidar cloud information can be utilized at multiple levels and the speed of data association can be accelerated according to the multi-scale data structure, thereby achieving robust feature extraction and fast scan-matching algorithms. First, on a large scale, the lidar point cloud data are classified according to the curvature into two parts: smooth collection and rough collection. Then, on a small scale, noise and unstable points in the smooth or rough collection are filtered, and edge points and corner points are extracted. Then, the proposed tangent-vector-pairs based on edge and corner points are applied to evaluate the rotation term, which is significant for producing a stable solution in motion estimation. We compare our performance with two excellent open-source SLAM algorithms, Cartographer and Hector SLAM, using collected and open-access datasets in structured indoor environments. The results indicate that our method can achieve better accuracy.

Description: In the single-polyelectrolyte aqueous phase separation (APS) approach, membranes are prepared by precipitating a weak polyelectrolyte from a concentrated aqueous solution using a pH switch. This has proven to be a versatile and more sustainable method compared to conventional approaches as it significantly reduces the use of organic solvents. Poly(styrene-alt-maleic acid) (PSaMA) is a polymer that has been extensively investigated for APS and has been the basis for both open and dense membranes with good performances. These membranes are chemically crosslinked and, in this work, we further investigated ultrafiltration (UF) and nanofiltration (NF) membranes prepared with PSaMA for their stability in various organic solvents and under different pH conditions. It was shown that these membranes had stable performances in both isopropanol (IPA) and toluene, and a slightly reduced performance in N-methyl-2-pyrollidone (NMP). However, PSaMA did not perform well as a selective layer in these solvents, indicating that the real opportunity would be to use the UF-type PSaMA membranes as solvent-stable support membranes. Additionally, the membranes proved to be stable in an acidic-to-neutral pH regime (pH 2–7); and, due to the pH-responsive nature of PSaMA, for the NF membranes, a pH-dependent retention of Mg2+ and SO42− ions was observed and, for the UF membranes, a strong responsive behavior was observed, where the pH can be used to control the membrane permeability. However, long-term exposure to elevated pH conditions (pH 8–10) resulted in severe swelling of the NF membranes, resulting in defect formation, and compaction of the UF membranes. For the UF membranes, this compaction did prove to be reversible for some but not all of the membrane samples measured. These results showed that in aqueous systems, membranes prepared with PSaMA had interesting responsive behaviors but performed best at neutral and acidic pH values. Moreover, the membranes exhibited excellent stability in the organic solvents IPA and toluene

Description: Background: After preterm birth, infants are at high risk for delays in language development. A promising intervention to reduce this risk is represented by the exposure to parental voices through book-reading in Neonatal Intensive Care Units (NICU). This study investigated the possible advantages of book-reading to preterm neonates during their NICU stay on their subsequent language development. Methods: 100 families of preterm infants were recruited. The parents of 55 preterm infants (Reading Group) received a colored picture-book on NICU admission and were supported to read to their neonate as often as possible and to continue after hospital discharge. Forty-five infants (Control Group) were recruited before the beginning of the intervention. Infant language development was assessed with the Hearing and Language quotients of the Griffith Mental Development Scale at the corrected ages of 3, 6, 9, 12, 18 and 24 months. Results: Regardless of group membership, Hearing and Language mean quotients decreased between 9 and 18 months; nevertheless, this decrease was considerably reduced in the Reading group, compared to the Control Group. Conclusions: Reading in NICUs represents a suitable intervention that could positively influence language development and parent-infant relationships in preterm children. The study findings support its implementation as a preventive measure.

Description: Due to their low density, magnesium alloys are very appealing for light-weight constructions. However, the use of the most common magnesium alloy, AZ91 (Mg 9 wt.% Al, 1 wt.% Zn), is limited to temperatures below 150 °C due to creep failure. Several alloys with an improved creep resistance have been developed in the past, for example the alloy MRI 230D or Ca-alloyed AZ91 variants. However, there is an ongoing discussion in the literature regarding the mechanisms of the improved creep resistance. One factor claimed to be responsible for the improved creep resistance is the intermetallic phases which form during casting. Another possible explanation is an increased creep resistance due to the formation of precipitates. To gain more insight into the improved creep resistance of MRI 230D, nanoindentation measurements have been performed on the different phases of as-cast, creep-deformed and heat-treated samples of MRI 230D and Ca-alloyed AZ91 variants. These nanoindentation measurements clearly show that the intermetallic phase (IP) of the alloy MRI 230D does not lose strength during creep deformation in contrast to the Ca-alloyed AZ91 variants. High-temperature nanoindentation measurements performed at 200 °C clearly show that the intermetallic phases of the MRI 230D alloy maintain their strength. This is in clear contrast to the Ca-alloyed AZ91 variants, where the IP is significantly softer at 200 °C than at room temperature. Atom probe measurements have been used to gain insight into the differences in terms of chemical composition between the IPs of MRI 230D and the Ca-alloyed AZ91 variants in order to understand the dissimilar behaviour in terms of strength loss with increasing temperature.

Description: Apart from numerous technical challenges, the transition towards a carbon-neutral energy supply is greatly hindered by limited economic feasibility of renewable energy sources. This results in their slow and bounded penetration in both commercial and residential sectors that are responsible for over 40% of final energy consumption. This paper aims to demonstrate that combined application of sophisticated planning methodologies at building-level and presents incentive mechanisms for renewables that can result in prosumers, featuring hybrid renewable energy systems (HRES), with economic performance comparable to that of conventional energy systems. The presented research enhances existing planning methodologies by integrating appliance-level demand side management into the decision process and investigates its effect on the planning problem. Moreover, the proposed methodology features an innovative and holistic approach that simultaneously assess electrical and thermal domain in both an isolated and grid-connected context. The analyzed hybrid system consists of solar photovoltaic, wind turbine and battery with thermal supply featuring solar thermal collector and a ground-source heat pump. Overall optimization problem is modeled as a mixed-integer linear program, while ranking of all feasible alternatives is made by the multicriteria decision-making algorithm against several technological, economic, and environmental criteria. A real-life scenario of energy system retrofit for a building in the United Kingdom was employed to demonstrate overall cost savings of 12% in the present market and regulation context.

Description: The paper addresses the sustainability of the European Union’s food consumption through a water footprint assessment of selected vulnerable agricultural imports from a two-pronged perspective: (1) the degree of the EU’s dependence on global green water resources embedded in the apparent consumption of selected water-intensive agricultural products and (2) the degree of commitment of countries of origin to sustainability policies. The study argues that the vulnerability of the EU’s agricultural imports to water risks can be estimated based on the amount of green water consumed in producing crops in the countries of origin. The results show that the EU’s consumption of agricultural goods is highly dependent on virtual water imports for all six selected vulnerable agricultural products, from the lowest footprint for bananas (5 mil. km3) to the largest for coffee (69 mil. km3). The analysis also points to a greater concern for quality issues in the countries of origin (56.53%) relative to management (26.52%) and availability issues (16.85%), but the latter are to arise in importance for sustainable production in the years to come. Our conclusions contribute to building up a responsible commitment towards (1) development of environmental policies and the design of practical measures by providing quantitative information that makes problems more clearly defined and tangible, and (2) assessing the outcome of policies and practical measures by understanding their effects on the sustainability of food consumption.

Description: ArcheoBot is a prototype of a Telegram Bot: it is an experimental prototype that builds on the common digital experiences of the authors of this article, aiming to offer a quick, powerful, easy to use tool. It aims to serve archaeological and topographical investigations quickly and to interface with other software for the management of collected data.

Description: We mainly focus on the effects of small changes of parameters on the dynamics of charged particles around Kerr black holes surrounded by an external magnetic field, which can be considered as a tidal environment. The radial motions of charged particles on the equatorial plane are studied via an effective potential. It is found that the particle energies at the local maxima values of the effective potentials increase with an increase in the black hole spin and the particle angular momenta, but decrease with an increase of one of the inductive charge parameter and magnetic field parameter. The radii of stable circular orbits on the equatorial plane also increase, whereas those of the innermost stable circular orbits decrease. On the other hand, the effects of small variations of the parameters on the orbital regular and chaotic dynamics of charged particles on the non-equatorial plane are traced by means of a time-transformed explicit symplectic integrator, Poincaré sections and fast Lyapunov indicators. It is shown that the dynamics sensitivity depends on small variations in the inductive charge parameter, magnetic field parameter, energy, and angular momentum. Chaos occurs easily as each of the inductive charge parameter, magnetic field parameter, and energy increases but is weakened as the angular momentum increases. When the dragging effects of the spacetime increase, the chaotic properties are not always weakened under some circumstances.

Description: The most common method used to pick up biomedical signals is through metallic electrodes coupled to the input of high-gain, low-noise amplifiers. Unfortunately, electrodes, amongst other effects, introduce an undesired contact resistance and a contact potential. The contact potential needs to be rejected since it would otherwise cause the saturation of the input stage of the amplifiers, and this is almost always obtained by inserting a simple RC high-pass filter in the input signal path. The contact resistance needs to be estimated to ensure that it does not impair correct measurements. Methods exist for estimating the contact resistance by dynamically modifying the input network configuration, but because of the presence of the input RC filter, long transients are induced any time a switch occurs between different input configurations, so that the measurement time may become unacceptably long. In this paper, we propose a new topology for a DC removal network at the input of the differential signal amplifier that results in an AC filter whose time constant can be continuously changed by means of a control voltage. As such, we can speed up the recovery from transients by setting very short time constants (during the input resistance estimation process) while maintaining the ability to obtain very low cut-in frequencies by setting a much larger time constant during actual measurements. A prototype of the system was built and tested in order to demonstrate the advantage of the approach we propose in terms of reduced measurement time.

Description: In the EU 28, the installed heating appliance stock is quite old, with an actual replacement rate of 4%. This is directly reflected in the average efficiency of the installed heating systems, where around 60% of the stock is rated with an energy class of C or D (the lowest classes of the energy label scale). The European project HARP aims at raising consumers’ awareness of the planned replacement of their old and inefficient heating appliances with more efficient and renewable solutions. In this direction, an energy labeling methodology for old appliances has been developed to rate the installed stock before the introduction of the EU energy label. The methodology has been developed for space heating appliances and water heaters, targeting two types of users: end consumers and professional users. The validation considered about 4600 space heating appliances and 800 water heaters built between 1972 and 2019. Three heating appliances and two water heaters were tested in the laboratory, confirming the reliability of the proposed methodology. The expected impact of defining an energy labeling methodology for installed heating appliances increases the current replacement rate of these appliances in the EU from 4% to 5%.

Description: This work presents a comprehensive theoretical analysis of current-mode power amplifiers as a function of input power for different biasing classes under the common simplifying assumption of constant transconductance and hard current cut-off/saturation. Typically, the theoretical analysis of power amplifier performance and behavior are carried out only at maximum output power. However, to achieve high data-rates, modern telecommunication systems adopt signals characterized by a very high peak-to-average power ratio, thus it is useful to analyze the power amplifier behavior as a function of power back-off. Moreover, in many cases, to enhance the efficiency and/or to apply harmonic shaping techniques, a clipped drain-source current, which approaches a square wave, is required. The classical analysis can be extended to low power levels only under the assumption of power-independent conduction angle, which is true only for class-A and class-B amplifiers, and does not take into account possible waveform clipping at maximum current. This work presents a complete theoretical Fourier analysis of FET-based power amplifiers as a function of quiescent drain-source current at any input power level and accounting for the clipped current case, up to the square-wave limit, reorganizing and completing the material that can be found in classical textbooks in the field.

Description: Hypoxia is known to impair mitochondrial and endoplasmic reticulum (ER) homeostasis. Post-hypoxic perturbations of the ER proteostasis result in the accumulation of misfolded/unfolded proteins leading to the activation of the Unfolded Protein Response (UPR). Mitochondrial chaperone TNF receptor-associated protein 1 (TRAP1) is reported to preserve mitochondrial membrane potential and to impede reactive oxygen species (ROS) production thereby protecting cells from ER stress as well as oxidative stress. The first-line antidiabetic drug Metformin has been attributed a neuroprotective role after hypoxia. Interestingly, Metformin has been reported to rescue mitochondrial deficits in fibroblasts derived from a patient carrying a homozygous TRAP1 loss-of-function mutation. We sought to investigate a putative link between Metformin, TRAP1, and the UPR after hypoxia. We assessed post-hypoxic/reperfusion longevity, mortality, negative geotaxis, ROS production, metabolic activity, gene expression of antioxidant proteins, and activation of the UPR in Trap1-deficient flies. Following hypoxia, Trap1 deficiency caused higher mortality and greater impairments in negative geotaxis compared to controls. Similarly, post-hypoxic production of ROS and UPR activation was significantly higher in Trap1-deficient compared to control flies. Metformin counteracted the deleterious effects of hypoxia in Trap1-deficient flies but had no protective effect in wild-type flies. We provide evidence that TRAP1 is crucially involved in the post-hypoxic regulation of mitochondrial/ER stress and the activation of the UPR. Metformin appears to rescue Trap1-deficiency after hypoxia mitigating ROS production and downregulating the pro-apoptotic PERK (protein kinase R-like ER kinase) arm of the UPR.

Description: Real-time PCR is widely used to study the relative abundance of mRNA due to its specificity, sensitivity, and repeatability quantification. However, relative quantification requires a reference gene, which should be stable in its expression, showing lower variation by experimental conditions or tissues. The aim of this study was to evaluate the stability of the expression of five commonly used reference genes (actb, ywhaz, b2m, sdha, and 18s rRNA) at different physiological stages (alert and emergency) in three different cattle breeds. In this study, five genes (actb, ywhaz, b2m, sdha, and 18s rRNA) were selected as candidate reference genes for expression studies in the whole blood from three cattle breeds (Romosinuano, Gyr, and Brahman) under heat stress conditions. The transcription stability of the candidate reference genes was evaluated using geNorm and NormFinder. The results showed that actb, 18SrRNA, and b2m expression were the most stable reference genes for whole blood of Gyr and Brahman breeds under two states of livestock weather safety (alert and emergency). Meanwhile, actb, b2m, and ywhaz were the most stable reference genes for the Romosinuano breed.

Description: Residents of nursing homes have been significantly affected by COVID-19 in Spain. The factors that have contributed to the vulnerability of this population are very diverse. In this study, physical agents, chemical pollutants, population density and different capacities of residences were analysed to understand their influence on the number of elderly people who have died in geriatric centres in different autonomous communities (AACCs) of Spain. A statistical analysis was carried out on the variables observed. The results show that many residences with a larger number of deaths were private, with some exceptions. Physical agents and pollutants were found to be determining factors, especially for the communities of Extremadura and Castilla–La Mancha, although the large number of factors involved makes this study complicated. The compromise between air quality and energy efficiency is of great importance, especially when human health is at stake.

Description: Contemporary agriculture has become very energy-intensive and mainly uses electricity, which is needed for technological processes on livestock farms. Livestock faeces are burdensome for the environment due to the release of methane into the atmosphere. This article presents the concept of a self-sufficient livestock farm as an off-grid energy circuit that is a part of the agricultural process. The key idea is to obtain an energy flow using the concept of a smart valve to achieve a self-sufficient energy process based on a biogas plant, renewable energy sources, and energy storage. During the production process, a livestock farm produces large amounts of waste in the form of grey and black manure. On the one hand, these products are highly harmful to the environment, but on the other, they are valuable input products for another process, i.e., methane production. The methane becomes the fuel for cogeneration generators that produce heat and electricity. Heat and electricity are partly returned to the main farming process and partly used by residents of the area. In this way, a livestock farm and the inhabitants of a village or town can become energy self-sufficient and independent of national grids. The idea described in this paper shows the process of energy production combining a biogas plant, renewable energy sources, and an energy storage unit that enable farmland to become fully self-sufficient through the energy flow between all constituents of the energy cycle being maintained by a smart valve.

Description: Due to the complex and variable conditions under which wind turbines operate, existing working condition classification methods are inadequate for condition assessment of the main transmission system. Because working conditions are too few after classification, it cannot effectively describe the complex and variable working conditions of wind turbine. This can lead to high false-alarm rates in the condition monitoring, which affect normal operations. This paper proposes a working condition classification method for the main transmission system of wind turbines based on supervisory control and data acquisition (SCADA) data. Firstly, correlation analysis of SCADA data acquired by wind farm is used to select the parameters relevant to the main transmission system. Secondly, according to the wind turbine control principle, the working conditions are initially divided into four phases: shutdown, start-up, maximum wind energy tracking, and constant speed. The k-means clustering algorithm is used to subdivide the maximum wind energy-tracking phase and constant speed phase, which account for a larger proportion of the working conditions, to achieve better classification. Finally, a case study is used to demonstrate the calculation of alarm thresholds and alarm rates for each working condition. The results are compared with the direct use of k-means clustering for working condition classification. It is concluded that the proposed method can significantly reduce the false-alarm rate of the vibration detection process.

Description: The basic premise of regional ecological construction would be to scientifically and effectively grasp the characteristics of land use change and its impact on landscape ecological risk. The research objects of this paper are the typical areas of the Yellow River Basin in China and “process-change-drive” as the logical main line. Moreover, this paper is based on multi-period land use remote sensing data from 2000 to 2020, the regional land use change process and influencing factors are identified, the temporal and spatial evolution and response process of landscape ecological risk are discussed, and the land use zoning control strategy to reduce ecological risk is put forward. The results indicated: (1) The scale and structure of land use show the characteristics of “many-to-one” and “one-to-many”; (2) the process of land use change is affected by the alternation of multiple factors. The natural environment and socio-economic factors dominate in the early stage and the location and policy factors have a significant impact in the later stage; (3) the overall landscape ecological risk level and conversion rate show a trend of “high in the southeast, low in the northwest”, shift from low to high and landscape ecological risks gradually increase; and (4) in order to improve the regional ecological safety and according to the characteristics of landscape ecological risk and spatial heterogeneity, we should adopt the management and control zoning method and set different levels of control intensity (from key intensity to strict intensity to general intensity), and develop differentiated land use control strategies.

Description: Climate change is expected to lead to changes to the amount, frequency, intensity, and timing of precipitation and subsequent water supply and its availability to plants in mountain regions worldwide. This is likely to affect plant growth and physiological performance, with subsequent effects to the functioning of many important high-elevation ecosystems. We conducted a quantitative systematic review and meta-analysis of the effects of altered water supply on plants from high elevation ecosystems. We found a clear negative response of plants to decreases in water supply (mean Hedges’ g = −0.75, 95% confidence intervals: −1.09 to −0.41), and a neutral response to increases in water supply (mean Hedges’ g = 0.10, 95% confidence intervals: 0.43 to 0.62). Responses to decreases in water supply appear to be related to the magnitude of change in water supply, plant growth form, and to the measured response attribute. Changes to precipitation and water supply are likely to have important consequences for plant growth in high elevation ecosystems, with vegetation change more likely be triggered by reductions than increases in growing season precipitation. High elevation ecosystems that experience future reductions in growing-season precipitation are likely to exhibit plant responses such as reduced growth and higher allocation of carbohydrates to roots.

Description: Voids in polymer matrix composites are one of the most common manufacturing defects, which may influence the mechanical properties and structural behavior of the final parts made of composites by various manufacturing methods. Therefore, numerous non-destructive testing (NDT) techniques were developed and applied for quality control and in-service testing of such structures. In this paper, the authors analyzed various alternatives to the reference technique, X-ray computed tomography (XCT) NDT, which is used for industrial testing of composite disks having defects in the form of the lower density areas. Different candidates, namely: vibration-based testing, infrared thermography, vibro-thermography, as well as ultrasonic testing were analyzed in terms of their sensitivity and technical feasibility. The quality of the results, the complexity of the testing procedure, time and labor consumption, and the cost of the equipment were analyzed and compared with the reference technique. Based on the conducted research the authors finally proposed a hybrid approach to quality control, using a combination of two NDT techniques–infrared thermography (for initial scanning and detection of near-surface defects) and ultrasonic testing (for a more detailed analysis of products that pass the first testing procedure). It allowed for replacing the costly XCT diagnostics with a much cheaper, but almost equally effective, alternative.

Description: Monitoring gait patterns in daily life will provide a lot of biological information related to human health. At present, common gait pressure analysis systems, such as pressure platforms and in-shoe systems, adopt rigid sensors and are wired and uncomfortable. In this paper, a biomimetic porous graphene–SBR (styrene-butadiene rubber) pressure sensor (PGSPS) with high flexibility, sensitivity (1.05 kPa−1), and a wide measuring range (0–150 kPa) is designed and integrated into an insole system to collect, process, transmit, and display plantar pressure data for gait analysis in real-time via a smartphone. The system consists of 16 PGSPSs that were used to analyze different gait signals, including walking, running, and jumping, to verify its daily application range. After comparing the test results with a high-precision digital multimeter, the system is proven to be more portable and suitable for daily use, and the accuracy of the waveform meets the judgment requirements. The system can play an important role in monitoring the safety of the elderly, which is very helpful in today’s society with an increasingly aging population. Furthermore, an intelligent gait diagnosis algorithm can be added to realize a smart gait monitoring system.

Description: For the sound field reconstruction of large conical surfaces, current statistical optimal near-field acoustic holography (SONAH) methods have relatively poor applicability and low accuracy. To overcome this problem, conical SONAH based on cylindrical SONAH is proposed in this paper. Firstly, elementary cylindrical waves are transformed into those suitable for the radiated sound field of the conical surface through cylinder-cone coordinates transformation, which forms the matrix of characteristic elementary waves in the conical spatial domain. Secondly, the sound pressure is expressed as the superposition of those characteristic elementary waves, and the superposition coefficients are solved according to the principle of superposition of wave field. Finally, the reconstructed conical pressure is expressed as a linear superposition of the holographic conical pressure. Furthermore, to overcome ill-posed problems, a regularization method combining truncated singular value decomposition (TSVD) and Tikhonov regularization is proposed. Large singular values before the truncation point of TSVD are not processed and remaining small singular values representing high-frequency noise are modified by Tikhonov regularization. Numerical and experimental case studies are carried out to validate the effectiveness of the proposed conical SONAH and the combined regularization method, which can provide reliable evidence for noise monitoring and control of mechanical systems.

Description: In the past few decades, ZrN thin films have been identified as wear resistant coatings for tribological applications. The mechanical and tribological properties of ZrN thin layers depend on internal stress induced by the adopted deposition techniques and deposition parameters such as pressure, temperature, and growth rate. In sputtering deposition processes, the selected target voltage waveform and the plasma characteristics also play a crucial influence on physical properties of produced coatings. In present work, ZrN thin films, obtained setting different values of duty cycle in a reactive bipolar pulsed dual magnetron sputtering plant, were investigated to evaluate their residual stress through the substrate curvature method. A considerable progressive increase of residual stress values was measured at decreasing duty cycle, attesting the significant role of voltage waveform in stress development. An evident correlation was also highlighted between the values of the duty cycle and those of wear factor. The performed analysis attested an advantageous effect of internal stress, having the samples with high compressive stress, higher wear resistance. A downward trend for wear rate with the increase of internal residual stress was observed. The choice of suitable values of duty cycle allowed to produce ceramic coatings with improved tribological performance.

Description: Individual identification plays an important part in disease prevention and control, traceability of meat products, and improvement of agricultural false insurance claims. Automatic and accurate detection of cattle face is prior to individual identification and facial expression recognition based on image analysis technology. This paper evaluated the possibility of the cutting-edge object detection algorithm, RetinaNet, performing multi-view cattle face detection in housing farms with fluctuating illumination, overlapping, and occlusion. Seven different pretrained CNN models (ResNet 50, ResNet 101, ResNet 152, VGG 16, VGG 19, Densenet 121 and Densenet 169) were fine-tuned by transfer learning and re-trained on the dataset in the paper. Experimental results showed that RetinaNet incorporating the ResNet 50 was superior in accuracy and speed through performance evaluation, which yielded an average precision score of 99.8% and an average processing time of 0.0438 s per image. Compared with the typical competing algorithms, the proposed method was preferable for cattle face detection, especially in particularly challenging scenarios. This research work demonstrated the potential of artificial intelligence towards the incorporation of computer vision systems for individual identification and other animal welfare improvements.

Description: The exploration and rational design of easily separable and highly efficient sorbents with satisfactory capability of extracting radioactive uranium (U)-containing compound(s) are of paramount significance. In this study, a novel magnetic hydroxyapatite (HAP) composite (HAP@ CoFe2O4), which was coupled with cobalt ferrite (CoFe2O4), was rationally designed for uranium(VI) removal through a facile hydrothermal process. The U(VI) ions were rapidly removed using HAP@ CoFe2O4 within a short time (i.e., 10 min), and a maximum U(VI) removal efficiency of 93.7% was achieved. The maximum adsorption capacity (Qmax) of the HAP@CoFe2O4 was 338 mg/g, which demonstrated the potential of as-prepared HAP@CoFe2O4 in the purification of U(VI) ions from nuclear effluents. Autunite [Ca(UO2)2(PO4)2(H2O)6] was the main crystalline phase to retain uranium, wherein U(VI) was effectively extracted and immobilized in terms of a relatively stable mineral. Furthermore, the reacted HAP@CoFe2O4 can be magnetically recycled. The results of this study reveal that the suggested process using HAP@CoFe2O4 is a promising approach for the removal and immobilization of U(VI) released from nuclear effluents.

Description: In this study, we develop physics-informed neural networks (PINNs) to solve an isothermal fixed-bed (IFB) model for catalytic CO2 methanation. The PINN includes a feed-forward artificial neural network (FF-ANN) and physics-informed constraints, such as governing equations, boundary conditions, and reaction kinetics. The most effective PINN structure consists of 5–7 hidden layers, 256 neurons per layer, and a hyperbolic tangent (tanh) activation function. The forward PINN model solves the plug-flow reactor model of the IFB, whereas the inverse PINN model reveals an unknown effectiveness factor involved in the reaction kinetics. The forward PINN shows excellent extrapolation performance with an accuracy of 88.1% when concentrations outside the training domain are predicted using only one-sixth of the entire domain. The inverse PINN model identifies an unknown effectiveness factor with an error of 0.3%, even for a small number of observation datasets (e.g., 20 sets). These results suggest that forward and inverse PINNs can be used in the solution and system identification of fixed-bed models with chemical reaction kinetics.

Description: As more and more fields utilize deep learning, there is an increasing demand to make suitable training data for each field. The existing interactive object segmentation models can easily make the mask label data because these can accurately segment the area of the target object through user interaction. However, it is difficult to accurately segment the target part in the object using the existing models. We propose a method to increase the accuracy of part segmentation by using the proposed interactive object segmentation model trained only with edge images instead of color images. The results evaluated with the PASCAL VOC Part dataset show that the proposed method can accurately segment the target part compared to the existing interactive object segmentation model and the semantic part-segmentation model.

Description: Lane and road marker segmentation is crucial in autonomous driving, and many related methods have been proposed in this field. However, most of them are based on single-frame prediction, which causes unstable results between frames. Some semantic multi-frame segmentation methods produce error accumulation and are not fast enough. Therefore, we propose a deep learning algorithm that takes into account the continuity information of adjacent image frames, including image sequence processing and an end-to-end trainable multi-input single-output network to jointly process the segmentation of lanes and road markers. In order to emphasize the location of the target with high probability in the adjacent frames and to refine the segmentation result of the current frame, we explicitly consider the time consistency between frames, expand the segmentation region of the previous frame, and use the optical flow of the adjacent frames to reverse the past prediction, then use it as an additional input of the network in training and reasoning, thereby improving the network’s attention to the target area of the past frame. We segmented lanes and road markers on the Baidu Apolloscape lanemark segmentation dataset and CULane dataset, and present benchmarks for different networks. The experimental results show that this method accelerates the segmentation speed of video lanes and road markers by 2.5 times, increases accuracy by 1.4%, and reduces temporal consistency by only 2.2% at most.

Description: Gait and physical fitness are related to cognitive function. A decrease in motor function and physical fitness can serve as an indicator of declining global cognitive function in older adults. This study aims to use machine learning (ML) to identify important features of gait and physical fitness to predict a decline in global cognitive function in older adults. A total of three hundred and six participants aged seventy-five years or older were included in the study, and their gait performance at various speeds and physical fitness were evaluated. Eight ML models were applied to data ranked by the p-value (LP) of linear regression and the importance gain (XI) of XGboost. Five optimal features were selected using elastic net on the LP data for men, and twenty optimal features were selected using support vector machine on the XI data for women. Thus, the important features for predicting a potential decline in global cognitive function in older adults were successfully identified herein. The proposed ML approach could inspire future studies on the early detection and prevention of cognitive function decline in older adults.

Description: The research presented in this paper examines the experiences of Poles traveling for leisure purposes in the summer season of 2020, taking into account the context of the COVID-19 pandemic. The study involved the analysis of source data, including statistical data, and a survey administered via the computer-assisted web interviewing (CAWI) method. The survey questionnaire was created on the Google platform. The link to the questionnaire was provided via social media to participants of travel groups in the period from 30 November 2020 to 15 February 2021. The sampling was purposive (included only travelers) despite efforts to maintain the gender balance; the proportion of women was higher. Therefore, caution must be applied when interpreting the results which may not be transferable. The survey included questions regarding the respondents’ travel behavior and risk perceptions. 433 correctly completed questionnaires were collected. The dataset was analyzed quantitatively and qualitatively. Descriptive statistics measures and correlation coefficients were used in the analysis of the results. The study shows that some respondents decided against traveling because of the pandemic situation, while those who decided to travel adjusted their behavior by avoiding crowded places and resigning from traveling abroad. Compliance with hygiene standards in the area of tourism services varied, and was the highest in the case of accommodation services. Women rated hygiene standards in chain cafes statistically higher than men and younger people rated hygiene on public transport, trains, air transport and in fast food services higher than older people. The higher the tourism expenditure, the lower the assessment of sanitary standards in tour guide services, air transport and chain cafes decreased.

Description: Carbon neutrality has positive impacts on people, nature and the economy, and buildings represent the “last mile” sector in the transition to carbon neutrality. Carbon neutrality is characterized by the decarbonization of operations and maintenance, in addition to zero emissions in electricity and other industry sectors. Taking China’s commercial buildings as an example, this study is the first to perform an extensive data analysis for a step-wise carbon neutral roadmap of building operations via the analysis of a dynamic emission scenario. The results reveal that the carbon emissions abatement of commercial building operations from 2001 to 2018 was 1460.85 (±574.61) mega-tons of carbon dioxide (Mt CO2). The carbon emissions of commercial building operations will peak in the year 2039 (±5) at 1364.31 (±258.70) Mt, with emission factors and energy intensity being the main factors influencing the carbon peak. To move toward carbon neutral status, an additional 169.73 Mt CO2 needs to be cut by 2060, and the low emission path toward carbon neutrality will lead to the realization of the carbon peak of commercial buildings in 2024, with total emissions of 921.71 Mt. It is believed that cutting emissions from the operation of buildings in China will require a multi-sectoral synergistic strategy. It is suggested that government, residents, enterprises, and other stakeholders must better appreciate the challenges to achieve a substantial carbon reduction and the need for urgent action in the building sector in order to achieve carbon neutrality.

Description: In this paper, a hybrid bat optimization algorithm based on variable neighbourhood structure and two learning strategies is proposed to solve a three-stage distributed assembly permutation flowshop scheduling problem to minimize the makespan. The algorithm is firstly designed to increase the population diversity by classifying the populations, which solves the difficult trade-off between convergence and diversity of the bat algorithm. Secondly, a selection mechanism is used to update the bat’s velocity and location, solving the difficulty of the algorithm to trade-off exploration and mining capacity. Finally, the Gaussian learning strategy and elite learning strategy assist the whole population to jump out of the local optimal frontier. The simulation results demonstrate that the algorithm proposed in this paper can well solve the DAPFSP. In addition, compared with other metaheuristic algorithms, IHBA has better performance and gives full play to its advantage of finding optimal solutions.

Description: Despite a keen interest in clinical research, most paramedical professionals are unwilling to play an active role. Our objective was to explore paramedical professionals’ representations of research. Using an existing database of final year paramedical students (speech therapy, occupational therapy, psychomotricity, audiometry, physiotherapy, orthoptics), we deployed a qualitative approach composed of two successive steps: (1) a free word association task, and (2) semi-structured individual interviews. Out of the 54 students who agreed to be contacted, we received 21 responses to the free word association questionnaire, and 11 interviews were conducted. The hierarchical evocation matrix revealed that the scientific representation of research is based on words defining the research and the purpose of the research. “Collaboration” was identified as being an essential part of the research process. The central core of the representation is coherent with all its components perceived as positive. The content analysis of the interviews showed a polarization around two key points: (1) participants are interested in accessing and using evidence in their practice (2) but feel less confident about and/or motivated to generate evidence themselves. This study highlights the need to develop more research-friendly environments, especially in training institutions.

Description: An approximate model based on friction-coefficient formalism is developed to predict the mixed-gas permeability and selectivity of polymeric membranes. More specifically, the model is a modification of Kedem’s approach to flux coupling. The crucial assumption of the developed model is the division of the inverse local permeability of the mixture component into two terms: the inverse local permeability of the corresponding pure gas and the term proportional to the friction between penetrants. Analytical expressions for permeability and selectivity of polymeric membranes in mixed-gas conditions were obtained within the model. The input parameters for the model are ideal selectivity and solubility coefficients for pure gases. Calculations have shown that, depending on the input parameters and the value of the membrane Peclét number (the measure of coupling), there can be both a reduction and an enhancement of selectivity compared to the ideal selectivity. The deviation between real and ideal selectivity increases at higher Peclét numbers; in the limit of large Peclét numbers, the mixed-gas selectivity tends to the value of the ideal solubility selectivity. The model has been validated using literature data on mixed-gas separation of n-butane/methane and propylene/propane through polymeric membranes.

Description: Artemisia annua L. is a herbaceous plant belonging to the Asteraceae family, known for producing, although at low levels, the sesquiterpene lactone artemisinin (AN), which is highly effective against malaria. In this study, an in vitro regeneration process of A. annua L. using ‘Artemis’ progeny was established and the potential of tissue culture for inducing new variability in terms of AN metabolism of in vitro regenerated plants was investigated. Among the plant growth regulators tested, the cytokinin 6-benzyladenine (BA) at 4.4 μM in combination with the auxin indole-butyric acid (IBA) at 0.35 μM yielded the greatest frequency of shoot induction. The optimal multiplication medium contained BA at 0.9 μM and naphthaleneacetic acid (NAA) at 0.05 μM. Regenerated plants (RPs), after transferring to the greenhouse and subsequently to the field, were analyzed during the growth cycle at different sampling times, showing a peak of AN content 20 days before blossom. Variability among different RPs and sampling times, in terms of AN and its precursors dihydroartemisinic acid (DHAA) and artemisinic acid (AA) was observed. This suggests that adventitious shoot induction could provide a useful strategy to induce variability influencing artemisinin metabolism as a consequence of in vitro manipulation.

Description: Cadmium (Cd) is one of the most injurious heavy metals, affecting plant growth and development. Melatonin (N-acetyl-5-methoxytryptamine) was discovered in plants in 1995, and it is since known to act as a multifunctional molecule to alleviate abiotic and biotic stresses, especially Cd stress. Endogenously triggered or exogenously applied melatonin re-establishes the redox homeostasis by the improvement of the antioxidant defense system. It can also affect the Cd transportation and sequestration by regulating the transcripts of genes related to the major metal transport system, as well as the increase in glutathione (GSH) and phytochelatins (PCs). Melatonin activates several downstream signals, such as nitric oxide (NO), hydrogen peroxide (H2O2), and salicylic acid (SA), which are required for plant Cd tolerance. Similar to the physiological functions of NO, hydrogen sulfide (H2S) is also involved in the abiotic stress-related processes in plants. Moreover, exogenous melatonin induces H2S generation in plants under salinity or heat stress. However, the involvement of H2S action in melatonin-induced Cd tolerance is still largely unknown. In this review, we summarize the progresses in various physiological and molecular mechanisms regulated by melatonin in plants under Cd stress. The complex interactions between melatonin and H2S in acquisition of Cd stress tolerance are also discussed.

Description: To respond to global climate change and achieve a “carbon peak” and “carbon neutrality” as soon as possible has become a common goal around the world. Economic growth relies heavily on financial development; indeed, low-carbon economic development is inseparable from financial support. This paper studies the impact of financial development on carbon emission intensity and its mechanism from both theoretical and empirical aspects. Based on the 2005–2018 data on Chinese cities and the Spatial Durbin Model (SDM) research results, this paper finds that: (1) Financial development has significantly reduced China’s carbon emission intensity overall. After considering spatial effects, financial development increases local carbon emission intensity, although it may lead to a more significant decrease in the surrounding area. (2) The analysis of heterogeneity shows that only the financial development in the eastern region has a substantial detrimental impact on total carbon emission intensity and the carbon emission intensity of neighboring cities. The financial development in the central and western regions has no significant effect on carbon emission intensity. (3) The mechanism test shows that financial development mainly reduces carbon emission intensity through technological innovation and structural optimization, with the effect of technological innovation being 9.5%, and the effect of structural optimization being 12.15%. The expansion of the consumption effects of financial development has no significant impact on carbon emission intensity. Accordingly, this article believes that it is necessary to further support financial development, build large-scale financial centers, continue to optimize the structure of financial products, and encourage the development of green finance.

Description: This study aimed to investigate the effects of multi-bacteria solid-state fermented diets with different crude fiber (CF) levels on growth performance, nutrient digestibility, and microbial flora of finishing pigs. The multi-bacteria solid-state fermented diets were made up of Lactobacillus amylovorus, Enterococcus faecalis, Bacillus subtilis, and Candida utilis. According to a 2 (factors) × 2 (levels) design, with the two factors being multi-bacteria solid-state fermentation (fed non-fermented diet or multi-bacteria fermentation) or CF levels (fed a basal diet containing 2.52% CF or 7.00% CF), a total of 36 finishing pigs (70.80 ± 5.75 kg) were divided into 4 treatments with 9 barrows per group: (1) pigs fed a diet containing 7.00% CF (HF), (2) pigs fed a multi-bacteria fermentation diet containing 7.00% CF (HFM), (3) pigs fed a diet containing 2.52% CF (LF), and (4) piglets fed a multi-bacteria fermentation diet containing 2.52% CF (LFM). This experiment lasted 28 days. The multi-bacteria solid-state fermented diet increased the backfat thickness (p 〈 0.05) and apparent total tract nutrient digestibility (ATTD) of CF, neutral detergent fiber (NDF), acid detergent fiber (ADF), crude protein (CP), 8 amino acids (Trp, Asp, Gly, Cys, Val, Met, Ile, and Leu), total essential amino acids (EAA), total non-essential amino acids (NEEA), and total amino acids (TAA) (p 〈 0.05). Multi-bacteria solid-state fermented diet increased serum concentrations of HDL-c, ABL, TP, and GLU, the serum enzyme activities of GSH-Px, T-AOC, SOD, and CAT (p 〈 0.05), the relative abundance of Lactobacillus, Oscillospira, and Coprococcus (p 〈 0.05), and the abundance of YAMINSYN3-PWY, PWY-7013, GOLPDLCAT-PWY, ARGORNPROST-PWY, and PWY-5022 pathways (p 〈 0.05). The multi-bacteria solid-state fermented diet reduced the digestion amount of CF, NDF, and ADF (p 〈 0.05), the serum concentrations of TC, TG, LDL-c, BUN, and MDA (p 〈 0.05), the relative abundance of Streptococcaceae (p 〈 0.05), and the abundance of PWY-6470, PWY0-862, HSERMETANA-PWY, LACTOSECAT-PWY, MET-SAM-PWY, PWY-6700, PWY-5347, PWY0-1061, and LACTOSECAT-PWY pathways (p 〈 0.05). The high-fiber diet increased average daily feed intake (p 〈 0.05), the serum concentrations of TC, TG, LDL-c, BUN, and MDA (p 〈 0.05), the relative abundance of Clostridiaceae_Clostridium and Coprococcus (p 〈 0.05), and the abundance of TCA-GLYOX-BYPASS, GLYCOLYSIS-TCA-GLYOX-BYPASS, and PWY-6906 pathways (p 〈 0.05). The high-fiber diet reduced chest circumference (p 〈 0.05) and ATTD of ether extract (EE), CF, NDF, ADF, Ca, CP, 18 amino acids (Trp, Thr, Val, Met, Ile, Leu, Phe, Lys, His, Arg Asp, Ser, Glu, Gly, Ala, Cys, Tyr, and Pro), EAA, NEAA, and TAA (p 〈 0.05). The high-fiber diet also reduced the serum concentrations of HDL-c, TP, ABL, and GLU, the serum enzyme activities of T-AOC, GSH-Px, SOD, and CAT (p 〈 0.05), and the relative abundance of Akkermansia and Oscillospira (p 〈 0.05). There was no significant effect of the interaction between multi-bacteria fermentation and dietary CF levels, except on the digestion amount of CF (p 〈 0.05). The 7.00% CF had a negative effect on the digestion of nutrients, but multi-bacteria solid-state fermentation diets could relieve this negative effect and increase backfat thickness. High-fiber diets and multi-bacteria solid-state fermentation improved the diversity and abundance of fecal microorganisms in finishing pigs.

Description: In this paper, we develop an economic order quantity (EOQ) model for fixed shelf-life items and a non-increasing demand. The objective of this model is to maximize the total profit. We find the criterion to decide (i) the interior maximum solution or (ii) the boundary maximum solution. Eight numerical examples are given to illustrate all possible scenarios of this generalized model. Our results identify a scenario for which the maximum profit is always negative. This is highly relevant for firms in the public sector operating at a financial loss.

Description: To explore the effects of thermal actions on the pore structural features of granite, scanning electron microscope (SEM) and mercury injection experiments were carried out on granite after thermal treatment (25 °C to 400 °C). The pore structure was investigated from various perspectives, including the capillary pressure curve, the pore–throat ratio, the median saturation pressure, the median pore–throat radius, the porosity, the pore volume, and the pore size distribution. Based on mercury intrusion test data, the Winland model of permeability prediction was modified for a high-temperature tight granite reservoir. The results showed that: (1) As the temperature rose, the mercury injection curve was gradually flattened, and the mercury ejection efficiency gradually increased. Meanwhile, the pore–throat ratio and the median saturation pressure decreased exponentially, and the pore connectivity was enhanced. (2) The median pore–throat radius and the porosity of granite increased exponentially as the temperature increased. Above 200 °C, the median pore–throat radius and the porosity increased substantially. (3) The pore volumes of the transitional pores, mesopores and macropores, and the total pore volume inside the granite, increased as the temperature rose. Especially above 200 °C, the transitional pores and the mesopores were prominently developed, and the pore volumes of the transitional pores and the mesopores took up a significantly greater proportion of the total pore volume. (4) As the temperature rose, the pore size distribution of granite became more extensive, the pore–throat structure was obviously developed, and the pore–throat connectivity was enhanced. (5) The relationship between the micropores’ characteristic parameters and the macro-permeability in engineering was established though a modified Winland model, and the modified Winland model had a better prediction effect. The findings provide a solid basis for rock geothermal mining projects and related geotechnical engineering.

Description: Chlorine-containing volatile organic compounds (CVOCs) present in industrial exhaust gas can cause great harm to the human body and the environment. In order to further study the catalytic oxidation of CVOCs, an active site regulated RuOx/Sn0.2Ti0.8O2 catalyst with different Ru precursors was developed. With Dichloromethane as the model molecule, the activity test results showed that the optimization of Ru precursor using Ru colloid significantly increased the activity of the catalyst (T90 was reduced by about 90 °C when the Ru loading was 1 wt%). The analysis of characterization results showed that the improvement of the catalytic performance was mainly due to the improvement of the active species dispersion (the size of Ru cluster was reduced from 3–4 nm to about 1.3 nm) and the enhancement of the interaction between the active species and the support. The utilization efficiency of the active components was improved by nearly doubling TOF value, and the overall oxidation performance of the catalyst was also enhanced. The relationship between the Ru loading and the catalytic activity of the catalyst was also studied to better determine the optimal Ru loading. It could be found that with the increase in Ru loading, the dispersibility of RuOx species on the catalyst surface gradually decreased, despite the increase in their total amount. The combined influence of these two effects led to little change in the catalytic activity of the catalyst at first, and then a significant increase. Therefore, this research is meaningful for the efficient treatment of CVOCs and further reducing the content of active components in the catalysts.

Description: One of the challenges in the future of food production, amidst increasing population and decreasing resources, is developing a sustainable food production system. It is anticipated that robotics will play a significant role in maintaining the food production system, specifically in labor-intensive operations. Therefore, the main goal of this project is to develop a robotic fruit harvesting system, initially focused on the harvesting of apples. The robotic harvesting system is composed of a six-degrees-of-freedom (DOF) robotic manipulator, a two-fingered gripper, a color camera, a depth sensor, and a personal computer. This paper details the development and performance of a visual servo system that can be used for fruit harvesting. Initial test evaluations were conducted in an indoor laboratory using plastic fruit and artificial trees. Subsequently, the system was tested outdoors in a commercial fruit orchard. Evaluation parameters included fruit detection performance, response time of the visual servo, and physical time to harvest a fruit. Results of the evaluation showed that the developed visual servo system has the potential to guide the robot for fruit harvesting.

Description: We report that polymerization makes a robust, practically applicable multifunctional optical device with a continuous wavelength tunable over 500 nm spectral range using UV-polymerizable cholesteric liquid crystals (CLCs). It can be used as a circular polarizer generating an extremely high degree of circularly polarized light with |g| = 1.85~2.00. It can also be used for optical notch filters, bandwidth-variable (from ~28 nm to ~93 nm) bandpass filters, mirrors, and intensity-variable beam splitters. Furthermore, this CLC device shows excellent stability owing to the polymerization of CLC cells. Its performance remains constant for a long time (~2 years) after a high-temperature exposure (170 °C for 1 h) and an extremely high laser beam intensity exposure (~143 W/cm2 of CW 532 nm diode laser and ~2.98 MW/cm2 of Nd: YAG pulse laser operation for two hours, respectively). The optical properties of polymerized CLC were theoretically analyzed by Berreman’s 4 × 4 matrix method. The characteristics of this device were significantly improved by introducing an anti-reflection layer on the device. This wavelength-tunable and multifunctional device could dramatically increase optical research efficiency in various spectroscopic works. It could be applied to many instruments using visible and near-infrared wavelengths.

Description: Surface modification of membranes is an effective approach for imparting unique characteristics and additional functionalities to the membranes. Chemical grafting is a commonly used membrane modification technique due to its versatility in tailoring and optimizing the membrane surface with desired functionalities. Various types of polymers can be precisely grafted onto the membrane surface and the operating conditions of grafting can be tailored to further fine-tune the membrane surface properties. This review focuses on the recent strategies in improving the surface design of liquid separation membranes through grafting-from technique, also known as graft polymerization, to improve membrane performance in wastewater treatment and desalination applications. An overview on membrane technology processes such as pressure-driven and osmotically driven membrane processes are first briefly presented. Grafting-from surface chemical modification approaches including chemical initiated, plasma initiated and UV initiated approaches are discussed in terms of their features, advantages and limitations. The innovations in membrane surface modification techniques based on grafting-from techniques are comprehensively reviewed followed by some highlights on the current challenges in this field. It is concluded that grafting-from is a versatile and effective technique to introduce various functional groups to enhance the surface properties and separation performances of liquid separation membranes.

Description: Mycotoxins are toxic secondary metabolites produced by fungi on agricultural produce. Mycotoxins can be cytotoxic, genotoxic, mutagenic, and teratogenic, and they are persistent threats to human and animal health. Consumption of mycotoxin-contaminated maize can cause cancer and even sudden death. Health hazards can also occur from consuming products from animals fed with mycotoxin-contaminated feed or forage. The main mode of spread of mycotoxigenic fungi is through air-borne spores originating from soil or plant debris, although some fungi can also spread through infected seed-to-seedling transmission, ultimately followed by contamination of the harvestable product. This perspective assesses opportunities to prevent mycotoxigenic fungal infection in maize seeds produced for sowing as an important starting point of crop contamination. A case study of Nigeria showed infection in all tested farmer-produced, seed company, and foundation seed samples. A schematic overview of the formal and informal seed systems is presented to analyze their contribution to fungal infection and mycotoxin contamination in the maize value chain, as well as to set criteria for successful control. We recommend an integrated approach to control mycotoxigenic fungal infection, including resistant varieties and other control methods during seed production, grain production, and grain storage, with an important role in maintaining seed health.

Description: Over the last years, the replacement of traditional polymer modifiers with waste plastics has attracted increasing interest. The implementation of such technology would allow a drastic reduction of both production cost and landfill disposal of wastes. Among all, polyethylene-based plastics have been proved suitable for this purpose. The research activities presented in this paper aim to assess the synergistic effect of polyethylene and Fischer–Tropsch waxes on the viscoelastic properties and performance of the bitumen. In order to reduce the blending time, waxes, and polyethylene need to be added simultaneously. In fact, the presence of the waxes reduces the polarity of the bitumen matrix and increases the affinity with the polymer promoting its dispersion. Results demonstrate that the chain length of the waxes, the form of the added waste polyethylene, and the blending protocol have critical effects on the time-evolution of such properties. Short-chain waxes have a detrimental impact on the rutting resistance regardless of the blending protocol. On the contrary, long-chain waxes improve the overall behavior of the polyethylene-modified binders and, in particular, the resistance to permanent deformations.

Description: In the first quarter of 2020, Italy became one of the earliest hotspots of COVID-19 infection, and the government imposed a lockdown. During the lockdown, an online survey of 2053 adults was conducted that asked about health behaviors and about the psychological and overall impact of COVID-19. The present study is a secondary analysis of that data. We hypothesized that self-control, higher socio-economic status, existing health conditions, and fear of infection were all inversely related to actions (or intentions) that violated the lockdown (i.e., infractions). Using partial least squares structural equation modeling (PLS-SEM), we found that only the fear of infection significantly dissuaded people from violating lockdown rules. Since it is not practical or ethical to sow a fear of infection, our study indicates that enacting rules and enforcing them firmly and fairly are important tools for containing the infection. This may become more important as vaccines become more widely available and people lose their fear of infection.

Description: Monitoring physical activity in medical and clinical rehabilitation, in sports environments or as a wellness indicator is helpful to measure, analyze and evaluate physiological parameters involving the correct subject’s movements. Thanks to integrated circuit (IC) technologies, wearable sensors and portable devices have expanded rapidly in monitoring physical activities in sports and tele-rehabilitation. Therefore, sensors and signal acquisition devices became essential in the tele-rehabilitation path to obtain accurate and reliable information by analyzing the acquired physiological signals. In this context, this paper provides a state-of-the-art review of the recent advances in electroencephalogram (EEG), electrocardiogram (ECG) and electromyogram (EMG) signal monitoring systems and sensors that are relevant to the field of tele-rehabilitation and health monitoring. Mostly, we focused our contribution in EMG signals to highlight its importance in rehabilitation context applications. This review focuses on analyzing the implementation of sensors and biomedical applications both in literature than in commerce. Moreover, a final review discussion about the analyzed solutions is also reported at the end of this paper to highlight the advantages of physiological monitoring systems in rehabilitation and individuate future advancements in this direction. The main contributions of this paper are (i) the presentation of interesting works in the biomedical area, mainly focusing on sensors and systems for physical rehabilitation and health monitoring between 2016 and up-to-date, and (ii) the indication of the main types of commercial sensors currently being used for biomedical applications.

Description: In Europe, the qualification of injection anchors in masonry under static and quasi-static actions is based on an assessment of tests performed in undamaged masonry. Nevertheless, in seismic prone countries like Italy the influences deriving from earthquake actions cannot be disregarded. Masonry elements are very sensitive to cyclic/seismic action and research on the behavior of anchors in damaged masonry is rather limited. The paper presents the results of an experimental campaign aimed at evaluating the residual tensile strength of adhesive anchors installed into undamaged walls that were subsequently subjected to cyclic in-plane loading to simulate seismic actions before. Consequently, the anchors experienced different stresses depending on their location within the walls. Overall, 29 tests were performed with anchors placed both, in undamaged and damaged areas. The results showed that there is a correlation between residual tensile strength and masonry initial conditions, and therefore the installation of anchors in masonry elements should be carefully planned avoiding areas that could be heavily damaged during seismic events or considering redundant connections in critical areas. In particular, it seems that the width of the crack (created by cyclic actions) that passes nearby/into the anchor borehole is the main parameter that affects the ultimate resistance of the anchors.

Description: The restoration of paintings always involves the removal of darkened superficial layers, which are mainly due to dust deposition and aged varnishes. As cleaning is an irreversible and invasive treatment, physical methods (i.e., laser cleaning) instead of chemical ones are frequently suggested to reduce side effects on pictorial layers. Among the most employed laser systems, the free-running Er:YAG laser is considered very suitable for fine arts cleaning. This laser works at 2.94 μm, at which only –OH and –NH bonds in molecules are excited. This character can become a disadvantage when pigments with these functional groups are present. To understand the potential of the Er:YAG laser in such situations or in the presence of degradable pigments, the effectiveness of varnish removal from paintings prepared with egg yolk as the binder and cinnabar and lead white as the pigments were systematically investigated. Different cleaning conditions were used, and a hyperspectral sensor was innovatively used as a rapid, in situ and non-destructive technique to assess the effects of laser ablation, besides microscopic analysis. Though results obtained show all these pigments are sensitive to this laser radiation, satisfactory cleaning can be achieved without damaging the pictorial layer. The best cleaning conditions were 0.5 W of power (50 mJ and 10 Hz for energy and frequency), with 2-propanol as the wetting agent.

Description: The development of nitrite-free meat products is a current industrial concern. Many efforts have been attempted to replace the nitrite effect in cured meats colour formation and pathogens control. Our previous work evidenced that lactic acid and a cold ripening were the best hurdle technologies for nitrite-free fermented sausages from metabolomics. In the first part of this work, we investigated the effect of lactic acid compared with both two alternative additives (glucono-D-lactone and a mix of sodium di-acetate/sodium lactate) and with low-nitrite sausages, all of them following either cold or traditional ripening. For this purpose, microbiological analysis, pH, water activity (aw), and a sensory study were performed. All nitrite-free sausages (cold or traditional ripened) showed quality and safety traits similar to low-nitrite traditionally ripened ones used as control. In addition, sensory study revealed that sausages with lactic acid were the most preferred cold ripened samples, supporting that this is an optimal strategy for the production of nitrite-free sausages. We selected this product for further studies. Indeed, in the second part, we evaluated the impact of ripening, and other hurdle technologies as High Pressure Processing (HPP) and under-vacuum storage against Listeria innocua and Salmonella spp. by a challenge test. Maximal declines were obtained for ripening along with HPP (i.e., 4.74 and 3.83 log CFU/g for L. innocua and Salmonella spp., respectively), suggesting that HPP might guarantee nitrite-free sausages safety. Although the quality of raw materials remains essential, these hurdle strategies largely contributed to nitrite-free sausages safety, offering a promising tool for the meat industry.

Description: Background: Salmonellaenterica is one of the common pathogens in both humans and animals that causes salmonellosis and threatens public health all over the world. Methods and Results: Here we determined the virulence phenotypes of nine Salmonellaenterica subsp. enterica (S. enterica) isolates in vitro and in vivo, including pathogenicity to chicken, cell infection, biofilm formation and virulence gene expressions. S. Enteritidis 211 (SE211) was highly pathogenic with notable virulence features among the nine isolates. The combination of multiple virulence genes contributed to the conferring of the high virulence in SE211. Importantly, many mobile genetic elements (MGEs) were found in the genome sequence of SE211, including a virulence plasmid, genomic islands, and prophage regions. The MGEs and CRISPR-Cas system might function synergistically for gene transfer and immune defense. In addition, the neighbor joining tree and the minimum spanning tree were constructed in this study. Conclusions: This study provided both the virulence phenotypes and genomic features, which might contribute to the understanding of bacterial virulence mechanisms in Salmonella enterica subsp. enterica. The first completed genomic sequence for the high virulent S. Enteritidis isolate SE211 and the comparative genomics and phylogenetic analyses provided a preliminary understanding of S. enterica genetics and laid the foundation for further study.

Description: A case study involving a healthy trained male athlete who completed a 786 km multi-stage ultra-trail race. Several markers were analyzed in blood and urine samples: creatinine (SCR) for kidney damage, sodium ([Na+]) for hyponatremia, creatine kinase (CK) for exertional rhabdomyolysis, as well as other hematological values. Samples were taken before and after the race and during the recovery period (days 2 and 9 after the race). Results showed: SCR = 1.13 mg/dL, [Na+] =139 mmol/L and CK = 1.099 UI/L. Criteria for the determination of acute kidney damage were not met, and [Na+] concentration was above 135 mEq/L, indicating the absence of hyponatremia. Exertional rhabdomyolysis was suffered by the athlete (baseline CK increased fivefold), though this situation was reverted after 9 days of recovery. Ultra-trail races cause biochemical changes in athletes, which should be known about by healthcare professionals.

Description: The catalytic process of glycerol hydrogenolysis to produce 1,2-propandiol (1,2-PD) in the absence of external hydrogen addition has been investigated. The methanol present in the crude glycerol from a biodiesel production process is used to provide in situ hydrogen produced via methanol steam reforming for the glycerol hydrogenolysis process. This process can reduce the additional cost for the transportation and storage of molecular hydrogen and also reduce the safety risks related to using high hydrogen pressure. It was found that the introduction of Pd onto a Cu/MgO/Al2O3 catalyst significantly improved the glycerol conversion and 1,2-PD selectivity. The pseudo-first-order kinetic results suggested that the promoting effect of Pd is primarily attributed to the enhanced activity for the hydrogenation of acetol, which is the intermediate formed via glycerol dehydration. A 27−3 fractional factorial design experiment was carried out to investigate the impacts of seven single factors and their binary effects on two responses, namely 1,2-PD selectivity and glycerol conversion. The results showed that the glycerol feed concentration has the most significant effect on the 1,2-PD selectivity, such that the 1,2-PD selectivity is lower if a more concentrated glycerol is used as the feedstock; stirring speed, inert gas pressure and water to methanol molar ratio have insignificant effects on the reaction system. The addition of Pd, higher temperature and higher catalyst loading are the essential factors in order to obtain a high selectivity of 1,2-PD and a high glycerol conversion.

Description: The last two decades have witnessed a significant development of fluorescent chemosensors with high sensitivity and selectivity, fast response and in situ detection [...]

Description: Coagulase is a critical factor for distinguishing Staphylococcus aureus and coagulase-negative Staphylococcus. Our previous studies demonstrated that the null mutation of coagulase (coa) or its direct regulator, SaeRS, significantly enhanced the ability of S. aureus (CA-MRSA 923) to survive in human blood in vitro. This led us to further investigate the role of coagulase and its direct regulator, SaeRS, in the pathogenicity of CA-MRSA 923 in bacteremia during infection. In this study, we found that the null mutation of coa significantly decreased the mortality of CA-MRSA 923; moreover, the single null mutation of saeRS and the double deletion of coa/saeRS abolished the virulence of CA-MRSA 923. Moreover, the mice infected with either the saeRS knockout or the coa/saeRS double knockout mutant exhibited fewer histological lesions and less neutrophils infiltration in the infected kidneys compared to those infected with the coa knockout mutant or their parental control. Furthermore, we examined the impact of coa and saeRS on bacterial survival in vitro. The null mutation of coa had no impact on bacterial survival in mice blood, whereas the deletion mutation of saeRS or coa/saeRS significantly enhanced bacterial survival in mice blood. These data indicate that SaeRS plays a key role in the lethality of CA-MRSA 923 bacteremia, and that coagulase is one of the important virulence factors that is regulated by SaeRS and contributes to the pathogenicity of CA–MRSA 923.

Description: The elementary particles of relativistic quantum field theory are not simple field quanta, as has long been assumed. Rather, they supplement quantum fields, on which they depend on but to which they are not reducible, as shown here with particles defined instead as a unified collection of properties that appear in both physical symmetry group representations and field propagators. This notion of particle provides consistency between the practice of particle physics and its basis in quantum field theory.

Description: Indigenous populations around the world face disproportionately high rates of disease related to the environment and animals. One Health is a concept that has been used effectively to understand and address these health risks. One Health refers to the relationships and interdependencies between animal, human, and environmental health and is an emerging research field that aligns with indigenous views of health. To understand the applicability of One Health in indigenous communities, a critical review was undertaken to investigate evidence of One Health research in indigenous communities internationally, assess the strength of evidence, and understand what gaps are present. This review included the appraisal of twenty-four studies based in five regions: Canada, Africa, Australia, South America, and Central America. The review found that there is a need for studies of high strength, with rigorous methods, local leadership, and active involvement of indigenous viewpoints, to be undertaken in indigenous communities internationally that focus on One Health. It highlights the need to further consider indigenous viewpoints in research to reduce limitations, increase effectiveness of findings, consider appropriateness of recommendations, and benefit communities.

Description: The impact of the COVID-19 pandemic on our lives is unquestionable, including in the area of substance consumption. This study aimed to evaluate the changes in the pattern of cannabis use during the Spanish COVID-19 lockdown and confinement, and to analyze the variations in the reported motives for cannabis use and withdrawal symptoms. A cross-sectional retrospective study was conducted between April and May 2020, using an instrument that included two time points. Time 1 collected retrospective information on the participants’ habits (N = 89; 73% male; mean age = 29.01) prior to confinement and Time 2 collected the same information during the confinement. Sociodemographic data were collected, as well as the frequency of substance use, cannabis use patterns, sources of cannabis, perceived availability of drugs and cannabis price, and the Marijuana Motives Measure questionnaire and the Cannabis Withdrawal Scale were used. Results showed a decrease in both cannabis use and consumption due to enhancement and social motives. All reported sources of cannabis experienced a reduction except for the Internet, which experienced a significant increase. There was a positive correlation between withdrawal symptoms and coping motives before and during the lockdown. These findings will allow professionals to better develop both prevention and intervention strategies.

Description: Stripping crystallization (SC) was introduced in this work to purify p-chlorophenol from the p-chlorophenol-rich liquid mixture and to purify m-chlorophenol from the m-chlorophenol-rich liquid mixture, respectively. Essentially, SC combines melt crystallization and vaporization to produce the solid product and the vapor from a liquid mixture via a series of three-phase transformations at reduced pressures during the cooling process. At the end of the SC, only the solid product remained while the liquid mixture was almost eliminated and the produced vapor was removed. A set of differential equations based on the mass and energy balances were proposed to determine the incremental variations of the amounts of remaining liquid, produced solid and produced vapor during the batch SC process. The experimental yield and product purity of the final product obtained from the batch SC experiments were compared with those predicted by the model.

Description: Small-size dredgers are used as a standard for dredging and maintaining the depth of the fairways to seaports, as well as of the ports themselves. These vessels are characterized by limited draft and a low freeboard. The safety of such craft, in terms of their stability, in relation to the conducted works is ensured by the observance of appropriate regulations and requirements. The use of these ships requires navigation between the ports in which they operate. Open sea navigation poses a threat to such vessels. The article presents two characteristic cases of overturning of vessels during sea towing. The requirements of existing freeboard regulations regarding the stability and stability of dredgers do not provide them with a sufficient level of safety at sea. Phenomena such as longitudinal and lateral swaying, wave boarding and dynamic action of the wind may lead to their overturning. The article deals with the problem of the influence of particular phenomena that threaten the stability of dredgers during sea navigation. The analysis of static and dynamic stability for various characteristic shapes of small dredgers is presented. The possibility of water entering the watertight compartments was also taken into account. The research was presented on the numerical models of dredgers. The main purpose of this paper was to assess the risks and possibilities of capsizing of small dredgers designated for port work and redevelopment during their sea voyage.

Description: Metal nanostructures exhibit specific optical characteristics owing to their localized surface plasmon resonance (LSPR) and have been studied for applications in various optical devices. The LSPR property strongly depends on the size and shape of metal nanostructures; thus, plasmonic devices must be designed and fabricated according to their uses. Nanoimprint lithography (NIL) is an effective process for repeatedly fabricating metal nanostructures with controlled sizes and shapes and require optical properties. NIL is a powerful method for mass-producible, low-cost, and large-area fabrication. However, the process lacks flexibility in adjusting the size and shape according to the desirable optical characteristics because the size and shape of metal nanostructures are determined by a single corresponding mold. Here, we conducted a re-shaping process through the air-plasma etching of a polymer’s secondary mold (two-dimensional nanopillar array made of cyclo-olefin polymer (COP)) to modulate the sizes and shapes of nanopillars; then, we controlled the spectral characteristics of the imprinted plasmonic devices. The relationship between the structural change of the mold, which was based on etching time, and the optical characteristics of the corresponding plasmonic device was evaluated through experiments and simulations. According to evaluation results, the diameter of the nanopillar was controlled from 248 to 139 nm due to the etching time and formation of a pit structure. Consequently, the spectral properties changed, and responsivity to the surrounding dielectric environment was improved. Therefore, plasmonic devices based on the re-shaped COP mold exhibited a high responsivity to a refractive index of 906 nm/RIU at a wavelength of 625 nm.

Description: A varied and well-planned diet can meet the nutritional needs of an athlete; however, in certain cases, it could be advisable to increase the intake of some vitamins, minerals or other components through the controlled intake of fortified foods or dietary supplements. In the European Union, a high number of sport foods and supplements are marketed; athletes could at times consume them indiscriminately or even choose products that have not been evaluated and approved by scientific evidence. In this sense, it is necessary to know and interpret the specific regulations for these products in order to make adequate use of them. The aim of this manuscript is to describe the current status of the European regulatory framework, focusing on: (1) regulation of the marketing and labelling of both fortified foods and supplements; (2) regulation of the use of substances used as ingredients in fortified foods; and (3) regulation of nutritional claims and/or health properties associated with nutrients, ingredients and other related substances. This review can facilitate knowledgeable decisionmaking by sports nutrition professionals in order to counsel or manage adequate food choices as well as help consumers make better-informed food decisions. Other experts, such as producers who ensure food safety, might also be interested in this review.

Description: In this paper, we provide external image features and use the internal attention mechanism to solve the VQA problem given a dataset of textual questions and related images. Most previous models for VQA use a pair of images and questions as input. In addition, the model adopts a question-oriented attention mechanism to extract the features of the entire image and then perform feature fusion. However, the shortcoming of these models is that they cannot effectively eliminate the irrelevant features of the image. In addition, the problem-oriented attention mechanism lacks in the mining of image features, which will bring in redundant image features. In this paper, we propose a VQA model based on adversarial learning and bidirectional attention. We exploit external image features that are not related to the question to form an adversarial mechanism to boost the accuracy of the model. Target detection is performed on the image—that is, the image-oriented attention mechanism. The bidirectional attention mechanism is conducive to promoting model attention and eliminating interference. Experimental results are evaluated on benchmark datasets, and our model performs better than other models based on attention methods. In addition, the qualitative results show the attention maps on the images and leads to predicting correct answers.

Description: Nutraceutical products possess various anti-inflammatory, antiarrhythmic, cardiotonic, and antioxidant pharmacological activities that could be useful in preventing oxidative damage, mainly induced by reactive oxygen species. Previously published data showed that a mixture of polyphenols and polyunsaturated fatty acids, mediate an antioxidative response in mdx mice, Duchenne muscular dystrophy animal model. Dystrophic muscles are characterized by low regenerative capacity, fibrosis, fiber necrosis, inflammatory process, altered autophagic flux and inadequate anti-oxidant response. FLAVOmega β is a mixture of flavonoids and docosahexaenoic acid. In this study, we evaluated the role of these supplements in the amelioration of the pathological phenotype in dystrophic mice through in vitro and in vivo assays. FLAVOmega β reduced inflammation and fibrosis, dampened reactive oxygen species production, and induced an oxidative metabolic switch of myofibers, with consequent increase of mitochondrial activity, vascularization, and fatigue resistance. Therefore, we propose FLAVOmega β as food supplement suitable for preventing muscle weakness, delaying inflammatory milieu, and sustaining physical health in patients affected from DMD.

Description: The need for line detection in images is growing rapidly due to its importance in many image processing applications. The selection of an appropriate line detection method is essential for accurate detection of line pixels, but few studies provide an analytical basis for selecting a specific line detection method. In this study, to solve the problem, a method to analytically determine the signal-to-noise ratio (SNR) of line detection methods is proposed. Three line detection methods were selected for comparison: edge-detection (ED)-based, second derivative (SD)-based, and the sum of gradient angle differences (SGAD)-based line detection methods. Then, this study quantifies the SNR of the three line detectors through error propagation and signal noise coupling. In addition, the derived SNRs are graphically visualized to explicitly compare the performance of line detectors. Then, the quantified SNRs were validated by showing that they are highly correlated with the completeness and correctness observed in the experiment with a set of natural images. The experimental results show that the proposed SNR analysis can be used to select or design a suitable line detector.

Description: Purpose: Both anatomic total shoulder arthroplasty (TSA) and shoulder hemiarthroplasty (SHA) are used for the management of end-stage glenohumeral osteoarthritis (GHOA). The present study compared TSA and SHA in terms of clinical outcome and complication rate. Methods: This meta-analysis followed the PRISMA guidelines. In October 2021, the following databases were accessed: Web of Science, Google Scholar, Pubmed, Scopus. All clinical trials comparing anatomical TSA versus SHA for GHOA were considered. Results: Data from 11,027 procedures were retrieved. The mean length of the follow-up was 81.8 (16 to 223.20) months. The mean age of the patients was 61.4 ± 8.6 years, and 56.0% (5731 of 10,228 patients) were women. At last follow-up, the age-adjusted constant score was greater following TSA (p 〈 0.0001), as were active elevation (p 〈 0.0001), flexion (p 〈 0.0001), abduction (p 〈 0.0001), and American Shoulder and Elbow Surgeons Shoulder Score (p 〈 0.0001). Postoperative pain (p 〈 0.0001) and revision rate (p = 0.02) were lower in the TSA group. Conclusions: Anatomic TSA performed better than SHA in patients with GHOA.

Description: There are still several unanswered questions regarding about ancient events in the Lithuanian population. The Lithuanians, as the subject of this study, are of great interest as they represent a partially isolated population maintaining an ancient genetic composition and show genetic uniqueness in European comparisons. To elucidate the genetic relationships between the Lithuania and North-Eastern European and West Siberian populations, we analyzed the population structure, effective population size, and recent positive selection from genome-wide single nucleotide polymorphism (SNP) data. We identified the close genetic proximity of Lithuanians to neighboring populations (Latvians, Estonians, Belarusians) and in part with West and South Slavs (Poles, Slovaks, and Slovenians), however, with particular genetic distinctiveness. The estimated long-term Ne values ranged from ~5900 in the Estonian population to ~2400 in the South Russian population. The divergence times between the Lithuanian and study populations ranged from 240 to 12,871 YBP. We also found evidence of selection in 24 regions, 21 of which have not been discovered in previous analyses of selection. Undoubtedly, the genetic diversity analysis of geographically specific regions may provide new insights into microevolutionary processes affecting local human populations.

Description: The nature and mechanisms of interaction between two selected methyl benzoate derivatives (methyl o-methoxy p-methylaminobenzoate–I and methyl o-hydroxy p-methylaminobenzoate–II) and model transport protein bovine serum albumin (BSA) was studied using steady-state and time-resolved spectroscopic techniques. In order to understand the role of Trp residue of BSA in the I-BSA and II-BSA interaction, the effect of free Trp amino acid on the both emission modes (LE–locally excited (I and II) and ESIPT–excited state intramolecular proton transfer (II)) was investigated as well. Experimental results show that the investigated interactions (with both BSA and Trp) are mostly conditioned by the ground and excited state complex formation processes. Both molecules form stable complexes with BSA and Trp (with 1:1 stoichiometry) in the ground and excited states. The binding constants were in the order of 104 M−1. The absorption- and fluorescence-titration experiments along with the time-resolved fluorescence measurements show that the binding of the I and II causes fluorescence quenching of BSA through the static mechanism, revealing a 1:1 interaction. The magnitude and the sign of the thermodynamic parameters, ΔH, ΔS, and ΔG, determined from van’t Hoff relationship, confirm the predominance of the hydrogen-bonding interactions for the binding phenomenon. To improve and complete knowledge of methyl benzoate derivative-protein interactions in relation to supramolecular solvation dynamics, the time-dependent fluorescence Stokes’ shifts, represented by the normalized spectral response function c(t), was studied. Our studies reveal that the solvation dynamics that occurs in subpicosecond time scale in neat solvents of different polarities is slowed down significantly when the organic molecule is transferred to BSA cavity.

Description: The present study was conducted to investigate how raw rapeseed cake (RRC), hydrobarothermally-treated rapeseed cake (HRC) and fermented rapeseed cake (FRC) fed to laying hens over a period of 12 weeks affected their performance, and the quality, fatty acid (FA) profile and oxidative stability of eggs. A total of 304 Hy-Line Brown laying hens at 36 weeks of age were distributed in a completely randomized design to four treatment groups with 38 replicates per treatment and two hens per replicate. The birds had ad libitum access to feed and water throughout the study. During the experiment, the birds were fed isonitrogenous and isocaloric diets in mash form, with various protein sources. In the control group (C), soybean meal (SBM) was the main source of dietary protein, whereas the experimental groups were fed diets containing 20% of RRC, HRC or FRC. Hydrobarothermal treatment and fermentation decreased the glucosinolate (GLS) content of RC, and fermentation reduced the concentration of phytate phosphorus (PP). In comparison with the RRC group, layers from the HRC and FRC groups were characterized by higher laying performance, comparable with that in group C. Irrespective of its physical form, RC added to layer diets adversely affected eggshell quality in all experimental groups, whereas albumen quality was highest in the FRC group. In comparison with group C, diets containing RRC, HRC and HRC led to a significant decrease in the content of saturated fatty acids (SFAs), an increase in the proportion of n-3 and n-6 polyunsaturated fatty acids (PUFAs) in the total FA pool in egg yolks, and a decrease in the n-6/n-3 PUFA ratio. The inclusion of RRC, HRC and FRC in layer diets decreased the activity of superoxide dismutase (SOD) in egg yolks, relative to group C. Group FCR eggs were characterized by the highest activity of catalase (CAT) and the lowest lipid peroxides LOOH concentration, compared with the remaining groups. The addition of RC to layer diets did not compromise the sensory quality of eggs, and eggs produced in group FRC received the highest overall score. It can be concluded that the inclusion of 20% RRC, HRC and FRC in layer diets does not compromise the sensory quality of eggs and has a beneficial influence on the FA profile and antioxidant potential of egg yolks. The use of FRC is recommended because it contributes to the highest laying performance, superior albumen quality and the highest sensory quality of eggs, relative to RRC and HRC.

Description: The heterotrimeric G-protein mediates growth and development by perceiving and transmitting signals in multiple organisms. Alternative splicing (AS), a vital process for regulating gene expression at the post-transcriptional level, plays a significant role in plant adaptation and evolution. Here, we identified five splicing variants of Gγ subunit gene TaGS3 (TaGS3.1 to TaGS3.5), which showed expression divergence during wheat polyploidization, and differential function in grain weight and size determination. TaGS3.1 overexpression significantly reduced grain weight by 5.89% and grain length by 5.04%, while TaGS3.2–3.4 overexpression did not significantly alter grain size compared to wild type. Overexpressing TaGS3.5 significantly increased the grain weight by 5.70% and grain length by 4.30%. Biochemical assays revealed that TaGS3 isoforms (TaGS3.1–3.4) with an intact OSR domain interact with WGB1 to form active Gβγ heterodimers that further interact with WGA1 to form inactive Gαβγ heterotrimers. Truncated isoforms TaGS3.2–3.4 , which lack the C-terminal Cys-rich region but have enhanced binding affinity to WGB1, antagonistically compete with TaGS3.1 to bind WGB1, while TaGS3.5 with an incomplete OSR domain does not interact with WGB1. Taking these observations together, we proposed that TaGS3 differentially regulates grain size via AS, providing a strategy by which the grain size is fine-tuned and regulated at the post-transcriptional level.

Description: After successful surgeries for patients with rhegmatogenous retinal detachment, the most common cause of retinal redetachment is proliferative vitreoretinopathy (PVR), which causes severe vision impairment and even blindness worldwide. Until now, the major treatment for PVR is surgical removal of the epiretinal membrane, while effective treatment to prevent PVR is still unavailable. Therefore, we investigated the potential of doxycycline, an antibiotic in the tetracycline class, to treat PVR using a mouse model. We used the human retinal pigment epithelial cell line, ARPE-19, for in vitro and in vivo studies to test doxycycline for PVR treatment. We found that doxycycline suppressed the migration, proliferation, and contraction of ARPE-19 cells with reduced p38 MAPK activation and total MMP activity. Intravitreal doxycycline and topical tetracycline treatment significantly ameliorated the PVR severity induced by ARPE-19 cells in mice. PVR increased the expression of MMP-9 and IL-4 and p38 MAPK phosphorylation and modestly decreased IL-10. These effects were reversed by doxycycline and tetracycline treatment in the mouse retina. These results suggest that doxycycline will be a potential treatment for PVR in the future.

Description: Wolfram syndrome (WS) 1 is a rare monogenic neurodegenerative disorder caused by mutations in the gene encoding WFS1. Knowledge of the pathophysiology of WS is incomplete and to date, there is no treatment available. Here, we describe early deviations in the renin-angiotensin-aldosterone system (RAAS) and bradykinin pathway (kallikrein kinin system, KKS) observed in a rat model of WS (Wfs1 KO) and the modulative effect of glucagon-like peptide-1 receptor agonist liraglutide (LIR) and anti-epileptic drug valproate (VPA), which have been proven effective in delaying WS progression in WS animal models. We found that the expression of key receptors of the RAAS and KKS, Agtr2 and Bdkrb1, were drastically downregulated both in vitro and in vivo at an early stage in a rat model of WS. Moreover, in Wfs1, KO serum aldosterone levels were substantially decreased and bradykinin levels increased compared to WT animals. Neither treatment nor their combination affected the gene expression levels seen in the Wfs1 KO animals. However, all the treatments elevated serum aldosterone and decreased bradykinin in the Wfs1 KO rats, as well as increasing angiotensin II levels independent of genotype. Altogether, our results indicate that Wfs1 deficiency might disturb the normal functioning of RAAS and KKS and that LIR and VPA have the ability to modulate these systems.

Description: Over the last few years, there has been a growing interest in the study of lightweight composite materials. Due to their tailorable properties and unique characteristics (high strength, flexibility and stiffness), glass (GFs) and carbon (CFs) fibers are widely used in the production of advanced polymer matrix composites. Glass Fiber-Reinforced Polymer (GFRP) and Carbon Fiber-Reinforced Polymer (CFRP) composites have been developed by different fabrication methods and are extensively used for diverse engineering applications. A considerable amount of research papers have been published on GFRP and CFRP composites, but most of them focused on particular aspects. Therefore, in this review paper, a detailed classification of the existing types of GFs and CFs, highlighting their basic properties, is presented. Further, the oldest to the newest manufacturing techniques of GFRP and CFRP composites have been collected and described in detail. Furthermore, advantages, limitations and future trends of manufacturing methodologies are emphasized. The main properties (mechanical, vibrational, environmental, tribological and thermal) of GFRP and CFRP composites were summarized and documented with results from the literature. Finally, applications and future research directions of FRP composites are addressed. The database presented herein enables a comprehensive understanding of the GFRP and CFRP composites’ behavior and it can serve as a basis for developing models for predicting their behavior.

Description: Forests (either natural or planted) play a key role in climate change mitigation due to their huge carbon-storing potential. In the 1980s, the Hellenic Public Power Corporation (HPPC) started the rehabilitation of lignite post-mining areas in Northwest Greece by planting mainly black locust (Robinia pseudoacacia L.). Today, these plantations occupy about 2570 ha, but the accumulation of Above Ground Biomass (AGB) and deadwood has not been assessed to date. Therefore, we aimed at estimating these biomass pools by calibrating an allometric model for AGB, performing an inventory for both pools and predicting the spatial distribution of AGB. 214 sample plots of 100 m2 each were set up through systematic sampling in a grid dimension of 500 × 500 m and tree dbh and height were recorded. AGB was estimated using an exponential allometric model and performing inventory measurements and was on average 57.6 t ha−1. Kriging analysis reliably estimated mean AGB, but produced errors in the prediction of high and low biomass values, related to the high fragmentation and heterogeneity of the studied area. Mean estimated AGB was low compared with European biomass yield tables for black locust. Similarly, standing deadwood was low (6–10%) and decay degrees were mostly 1 and 2, indicating recent deadwood formation. The overall low biomass accumulation in the studied black locust restoration plantations may be partially attributed to their young age (5–30 years old), but is comparable to that reported in black locust restoration plantation in extremely degraded sites. Thus, black locust successfully adapted to the studied depositions of former mines and its accumulated biomass has the potential to improve the carbon footprint of the region. However, the invasiveness of the species should be considered for future management planning of these restoration plantations.

Description: The variance κ1 of the natural time analysis of earthquake catalogs was proposed in 2005 as an order parameter for seismicity, whose fluctuations proved, in 2011, to be minimized a few months before the strongest mainshock when studying the earthquakes in a given area. After the introduction of earthquake networks based on similar activity patterns, in 2012, the study of their higher order cores revealed, in 2019, the selection of appropriate areas in which the precursory minima βmin of the fluctuations β of the seismicity order parameter κ1 could be observed up to six months before all strong earthquakes above a certain threshold. The eastern Mediterranean region was studied in 2019, where all earthquakes of magnitude M≥7.1 were found to be preceded by βmin without any false alarm. Combining these results with the method of nowcasting earthquakes, introduced in 2016, for seismic risk estimation, here, we show that the epicenter of an impending strong earthquake can be estimated. This is achieved by employing—at the time of observing the βmin—nowcasting earthquakes in a square lattice grid in the study area and by averaging, self-consistently, the results obtained for the earthquake potential score. This is understood in the following context: the minimum βmin is ascertained to almost coincide with the onset of Seismic Electric Signals activity, which is accompanied by the development of long range correlations between earthquake magnitudes in the area that is a candidate for a mainshock.

Description: Our research was designed to evaluate the effect on bone regeneration with 3-dimensional (3D) printed polylactic acid (PLA) and 3D printed polycaprolactone (PCL) scaffolds, determine the more effective option for enhancing bone regeneration, and offer tentative evidence for further research and clinical application. Employing the 3D printing technique, the PLA and PCL scaffolds showed similar morphologies, as confirmed via scanning electron microscopy (SEM). Mechanical strength was significantly higher in the PLA group (63.4 MPa) than in the PCL group (29.1 MPa) (p 〈 0.01). Average porosity, swelling ratio, and degeneration rate in the PCL scaffold were higher than those in the PLA scaffold. SEM observation after cell coculture showed improved cell attachment and activity in the PCL scaffolds. A functional study revealed the best outcome in the 3D printed PCL-TGF-β1 scaffold compared with the 3D printed PCL and the 3D printed PCL-Polydopamine (PDA) scaffold (p 〈 0.001). As confirmed via SEM, the 3D printed PCL- transforming growth factor beta 1 (TGF-β1) scaffold also exhibited improved cell adhesion after 6 h of cell coculture. The 3D printed PCL scaffold showed better physical properties and biocompatibility than the 3D printed PLA scaffold. Based on the data of TGF-β1, this study confirms that the 3D printed PCL scaffold may offer stronger osteogenesis.

Description: Beneficial effects of n-3 fatty acids on metabolic biomarkers in patients with type 2 diabetes (T2DM) has been reported. The objectives of this current research were to investigate the effects of n-3 supplementation on metabolic factors, weight, and body mass index (BMI) in patients with type 2 diabetes mellitus (T2DM), using a meta-analysis of randomized, controlled trials (RCTs). Online databases PubMed, Embase, Web of Science, and Science Direct were searched until 2021 to identify eligible articles. Thirty-two trials were included. The results showed that n-3 consumption can significantly reduce glycemic factors including fasting blood sugar (FBS) (−0.36 (−0.71 to −0.01)), glycated hemoglobulin (HbA1c) (−0.74 (−1.13 to −0.35)), and homeostatic model assessment of insulin resistance (HOMA.IR) (−0.58 (−1.13 to −0.03)). Furthermore, significant improvement in lipid profile including triglycerides (TG) (−0.27 (−0.37 to −0.18)), total cholesterol (−0.60 (−0.88 to −0.32)), low density lipoprotein (LDL) (−0.54 (−0.85 to −0.23)), and high-density lipoprotein (HDL) (0.60 (0.23 to 0.96)) levels were found in the present meta-analysis. The reduction in the inflammatory marker’s tumor necrosis factor-alpha (TNF-α) (−0.13 (−0.75 to 0.48)) and c-reactive protein (CRP) (−0.72 (−1.70 to 0.27)), as well as weight (−0.09 (−0.24 to 0.07)) and BMI (−0.13 (−0.29 to 0.02)) were not statistically significant. Furthermore, the findings revealed that the optimal dose and duration of n-3 consumption for patients with T2DM is 1000–2000 mg/d for more than 8 weeks. The present meta-analysis and review reveals that n-3 supplementation can improve glycemic factors and lipid profile in patients with T2DM. Furthermore, n-3 supplementation may provide beneficial effects on inflammatory markers and body weight if used at the appropriate dose and duration.

Description: Global climatic changes have been observed for all natural biomes, with the greatest impact in the permafrost zone. The short series of direct observations of air temperature and precipitation from meteorological stations for this territory make it difficult to use them in studies of the impact of climate change on forest and forest-tundra ecosystems, but only longer series of gridded data expand the temporal-spatial resolution of this analysis. We compared local and gridded air temperature, precipitation and vapor pressure deficit (VPD) data, analyzed the trends of their changes over the last century for three sites in the permafrost zone (YAK and TAY in Russia, and CAN in Canada), and estimated the effect of their variability on oxygen isotopes in the tree-ring cellulose (δ18Ocell) of three different species (Larix cajanderi Mayr, Larix gmelinii Rupr. Rupr and Piceaglauca (Moench) Voss). Climate trend analysis showed strong changes after the 1980s, and even more pronounced from 2000 to 2020. We revealed that δ18Ocell-YAK showed mixed signals of the July temperature (r = 0.49; p = 0.001), precipitation (r = −0.37; p = 0.02) and vapor pressure deficit (VPD) (r = 0.31; p = 0.02), while δ18Ocell-CAN captured longer March–May (r = 0.37, p = 0.001) and July (r = 0.32, p 〈 0.05) temperature signals as well as spring VPD (r = 0.54, p = 0.001). The δ18Ocell-TAY showed a significant correlation with air temperature in July (r = 0.23, p = 0.04) and VPD in March (r = −0.26, p = 0.03). The obtained eco-hydrological relationships indicate the importance of temperature and moisture to varying degrees, which can be explained by site- and species-specific differences.

Description: Ditch-pond systems can effectively alleviate the adverse effects of agricultural drainage on downstream canals and flood control in downstream areas. In this study, peak flow reduction rate (PFR) and drainage volume detention rate (DVD) are used to evaluate the effectiveness of an off-line ditch-pond system for reducing peak flow, retarding agricultural drainage water, and examining the key influencing factors. The results show that the PFR and DVD of the off-line ditch-pond system are significantly affected by three parameters: weir depth (Ld), weir width (Lw), and pond area-to-drainage area ratio (Ksp). Both the PFR and DVD increase with the increase in Ld, Lw, and Ksp. The effects of Ld and Lw on the PFR and the DVD are significant, whereas that Ksp is relatively small. Adjusting Ld and Lw increases both the PFR and DVD up to 80%. Specifically, Ld contributes 75% of the variations in the PFR and the DVD, and Lw affects only 17% of the PFR variations and 11% of the DVD variations. These findings confirm that an off-line ditch-pond system can be effectively used for the detention of agricultural drainage water. Thus, when such a system is designed with an appropriate diversion weir, the impact of agricultural drainage water on downstream canals and downstream areas can be reduced remarkably.

Description: Recombination of charge carriers can affect the response of ionization detectors used for the dosimetry of radiotherapy fields. In this work, we present a method for correcting online the recombination effects in arrays of ionization chambers irradiated with time-varying dose rates. The method is based on the characterization of the dose rate/recombination response of the detector, and the measurement of the instant ionization current in the detector, rather than the integrated charge. The proposed method was investigated with simulations of the response of different air and liquid ionization chambers in situations where recombination can be large. In addition, we experimentally investigated the application of the method with an in-house-developed liquid-filled ionization chamber. The proposed online correction method can compensate for recombination losses and seems feasible to implement in the software of ionization arrays/detectors used for the dosimetry of radiotherapy fields.

Description: Background/Aim: The recovery pattern of hepatitis C virus (HCV)-associated metabolic alteration after sustained virological response (SVR) following direct-acting antivirals (DAAs) remains elusive. Methods: A prospective cohort study of chronic HCV-infected (CHC) patients (n = 415) receiving DAAs (n = 365) was conducted. Metabolic profiles were examined in SVR patients (n = 360) every 3–6 months after therapy and compared with those of sex- and age-matched controls (n = 470). Results: At baseline, of 415, 168 (40.5%) had insulin resistance (IR). The following were associated: levels of high-density lipoprotein cholesterol (HDL-C), triglycerides (TGs), HCV RNA, fibrosis-4 score, and interferon-λ3-rs12979860 genotype with total cholesterol (TC) levels; and TG levels and BMI with HOMA-IR. Over a 3-year follow-up, in SVR patients, BMI and TC levels and TG/HDL-C ratios increased from baseline, while HOMA-IR trended downward by 72 weeks after therapy and then increased. The increased HDL-C levels began to decrease after 72 weeks after therapy. TC and HOMA-IR were negatively associated with each other until 24 weeks after therapy. Earlier increases in BMI and decreases in HOMA-IR were noted in SVR patients with than in those without baseline IR. Compared with controls, in the subgroup without baseline IR, SVR patients had increased BMI and HOMA-IR levels. Metabolic profiles were similar between SVR patients and controls in the subgroup with baseline IR. Conclusions: In SVR patients treated with DAAs, the recovery of altered lipid and glucose metabolism was not coupled until 72-week post-therapy, when HOMA-IR reached its nadir. SVR patients with baseline IR recovered from HCV-associated metabolic alterations earlier than those without baseline IR.

Description: The main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal thermal and flow parameters requires the knowledge of the theory of heat exchangers as well as measurement methods and numerical calculations. Bearing in mind the above, the liquid crystal techniques (LCT), particle image velocimetry (PIV) and digital image processing (DIP) for temperature, velocity, friction factor and heat transfer coefficient measurements are presented herein. These three optical tools (using desktop computers) create an extremely powerful and advanced measuring technique that has not been available anywhere before. Brief histories of these measurement methods and techniques are discussed and some examples are presented. In order to assess and select the value of the measurement technique, local and average distributions of Nusselt numbers (in the measurement section) obtained by the transit analysis method on the inter-rib regions of a plate coated by thermochromics liquid crystal and heated by air as an alternative to the steady-state analysis. In the parallel, numerical calculation was performed with the use of the ANSYS Fluent software code and supported by laser anemometry-computed turbulence intensity of air flow. Comparison of the Nusselt number distributions was determined by three methods, i.e., steady state, the transient method and CFD simulation. Up to three-fold enhancement of the local heat transfer capability was observed. Failure to take into account the surface of the ribs in heat transfer causes differences in the obtained results of the Nusselt number depending on the method used. Apart from the heat transfer data, the pressure drop in the form of friction factors is also presented. On the basis of the conducted research, it can be stated that both qualitative and quantitative coherence was obtained between the experimental and computational studies.

Description: The use of polymer composite materials in the aeronautics and automotive sectors has increased dramatically, and their fire behaviour has become a critical parameter in terms of fire safety. On this premise, it is critical to demonstrate that these composite materials constitute elements whose safety justifies a high level of confidence. This is based on their combustibility and the rate at which flammable and toxic gaseous species are emitted. Thus, strict fire safety regulations are enforced by the relevant authorities concerned because of their potential fire risk. This study analysed papers published between 1970 and 2021 that described the devices used to characterise the thermal behaviour of composite materials at various scales. The objective was to highlight the thermophysical phenomena, making it possible to accurately assess the flammability and thermal stability of polymer composite materials. The results of this research reveal that the small-scale facilities provide detailed understanding and mastery of the thermal reaction properties of the composites. While with the medium scale, the extended fire reaction parameters, which are the key indicators of the fire safety performance, can be determined. On a large scale, the tests were carried out using devices such as the NexGen burner recommended by the FAA. Therefore, with such assays, it is possible to assess the rates of thermal degradation as well as quantified pyrolysis gases. However, compared to other scales, there were very few works on a large scale. In addition, by focusing on the polluting nature of synthetic composite materials, there is also few research studies aimed at designing new polymer composite materials from biological sources.

Description: Vaccinium emarginatum Hayata is a medicinal plant that has been historically used in ethnopharmacy to treat diseases in Taiwan. The objective of this study is to evaluate the anti-cancer and anti-bacterial constitutes from the root nodule extract of V. emarginatum. The chemical composition of V. emarginatum fractions was analyzed by high-performance liquid chromatography-electrospray ionization tandem mass spectrometry (HPLC-ESI-MS/MS) and the chemical constitutes were isolated and structurally identified by nuclear magnetic resonance (NMR) spectroscopy. Bioassay-guided chromatography showed that the ethyl acetate (EA) fraction was bioactive on the hepatocellular carcinoma (HepG2). By LC-ESI-MS/MS analysis, twenty peaks of EA fraction were partially identified and the phytochemical investigation of the fractions led to the isolation and identification of protocatuchuic acid (1), epicatechin (2), catechin (3), procyanidin B3 (4), procyanidin A1 (5), hyperin (6), isoquercetin (7), quercetin (8), lupeol (9), beta-amyrin (10), and alpha-amyrin (11). Both procyanidin B3 and A1 exhibited anti-proliferative activity against HepG2 and gastric adenocarcinoma (AGS) cells at IC50 values between 38.4 and 41.1 μM and 79.4 and 83.8 μM, respectively. In addition, isoquercetin displayed the strongest anti-proliferative activity against the HepG2, lung carcinoma (A549), and AGS cell at 18.7, 24.6 and 68.5 μM, respectively. Among the triterpenoids, only lupeol showed the inhibitory activity against all tested tumor cell lines at IC50 values between 72.9 and 146.8 μM. Furthermore, procyanidins B3, A1 and isoquercetin displayed moderate anti-bacterial activity against Staphylococcus aureus. In conclusion, this study provides background information on the exploitation of V. emarginatum as a potential natural anti-cancer and anti-bacterial agent in pharmaceutical research.

Description: Background: The objective of this systematic review and meta-analysis was to examine the reliability of isokinetic measurements of hip strength in flexion and extension in healthy subjects and athletes. Methods: The databases used were Web of Science, SCOPUS, Medline and PubMed. R was used for all statistical analyses. Results: Hip flexion shows moderate reliability in the supine position (ICC = 0.72; 95% CI: 0.46–0.99) and good reliability in the standing position (ICC = 0.79; 95% CI: 0.54–1.04). Hip extension shows excellent reliability in the supine position (ICC = 0.90; 95% CI: 0.85–0.96) and moderate reliability in the standing position (ICC = 0.72; 95% CI: 0.48–0.96). Flexion of 120°/s and 180°/s showed excellent reliability (ICC = 0.93; 95% CI: 0.85–1.00), (ICC = 0.96; 95% CI: 0.92–1.01). The 60°/s and 120°/s extension showed good reliability (ICC = 0.90; 95% CI: 0.82–0.98), (ICC = 0.87; 95% CI: 0.75–0.99). The 180°/s extension presented excellent reliability (ICC = 0.93; 95% CI: 0.82–1.03). Conclusions: The standing position shows good reliability for hip flexion and the supine position shows excellent reliability for hip extension, both movements have excellent reliability at velocities between 120°/s to 180°/s.

Description: Tranilast (TRL), a synthetic derivative of a tryptophan metabolite, is an anti-allergic drug used to treat bronchial asthma. We investigated how TRL activated the nuclear factor-erythroid 2 p45-related factor 2 (Nrf2)-hemeoxygenase-1 (HO-1) pathway based on the electrophilic chemistry of the drug and whether TRL activity contributed to the treatment of rat colitis. In human colon carcinoma cells, TRL activated Nrf2, as represented by an increase in nuclear Nrf2 and induction of Nrf2-dependent luciferase and, subsequently, HO-1, a target gene product of Nrf2. TRL activation of Nrf2 and induction of HO-1 were completely prevented by chemical reduction of the electrophilic functional group (α, β-unsaturated carbonyl group) in the drug. In parallel, TRL was reactive with the nucleophilic thiol group in N-acetylcysteine, forming a covalent adduct. Moreover, TRL, but not reduced TRL, binds to Kelch-like ECH-associated protein 1 (KEAP1), releasing Nrf2. TRL administration ameliorated colonic damage and inflammation in rats with dinitrobenzene sulfonic acid-induced colitis, which was partly compromised by the chemical reduction of TRL or co-treatment with an HO-1 inhibitor. Our results suggest that TRL activated the Nrf2-HO-1 pathway via covalent binding to KEAP1, partly contributing to TRL amelioration in rat colitis.

Description: Calcareous and siliceous CDW wastes from concrete and glass wastes when mixed in binary mixtures has been analyzed in this study. Fine CDW fractions (

Description: Objective: To test the efficacy of the Athletics Injury Prevention Programme (AIPP) to reduce the percentage of athletes presenting at least one injury complaint leading to participation restriction (ICPR) over an athletics season. Methods: During the 2017–2018 athletics season, we included in this cluster randomised controlled trial (ClinicalTrials.gov Identifier: NCT03307434) 840 athletes randomly assigned (randomisation unit: athletic clubs) to a control group (regular training) or to an intervention group (regular training plus the AIPP 2/week). Using a weekly online questionnaire, athletes reported the ICPR, training and competition exposures, and, for the intervention group, the compliance with the AIPP. The primary outcome was the percentage of athletes presenting at least one ICPR over the study follow-up. Results: A total of 449 and 391 athletes were included in the intervention and control groups, respectively. From them, 68 (15.1%) and 100 (25.6%) athletes, respectively, provided 100% of the requested information during the follow-up (39 weeks). A total of 6 (8.8%) performed the AIPP 2/week or more. The proportion of athletes who had at least one ICPR over the follow-up period was similar in the intervention (64.7%) and control groups (65.0%), with adjusted odds ratios: 0.81 (95% CI 0.36 to 1.85). There were no between-group differences when comparing separately the subgroups corresponding with the different compliance levels. Conclusion: This cluster randomised controlled trial reported no efficacy of the AIPP. However, the overall response proportion and the compliance with the AIPP in the intervention group were low. In individual sports especially, efforts should be first made to improve the implementation and adoption of interventions.

Description: The gut microbiota is a crucial factor in maintaining homeostasis. The presence of commensal microorganisms leads to the stimulation of the immune system and its maturation. In turn, dysbiosis with an impaired intestinal barrier leads to accelerated contact of microbiota with the host’s immune cells. Microbial structural parts, i.e., pathogen-associated molecular patterns (PAMPs), such as flagellin (FLG), peptidoglycan (PGN), lipoteichoic acid (LTA), and lipopolysaccharide (LPS), induce inflammation via activation of pattern recognition receptors. Microbial metabolites can also develop chronic low-grade inflammation, which is the cause of many metabolic diseases. This article aims to systematize information on the influence of microbiota on chronic inflammation and the benefits of microbiota modification through dietary changes, prebiotics, and probiotic intake. Scientific research indicates that the modification of the microbiota in various disease states can reduce inflammation and improve the metabolic profile. However, since there is no pattern for a healthy microbiota, there is no optimal way to modify it. The methods of influencing microbiota should be adapted to the type of dysbiosis. Although there are studies on the microbiota and its effects on inflammation, this subject is still relatively unknown, and more research is needed in this area.

Description: Glioblastoma (GBM) is the most prevalent primary brain cancer in the pediatric and adult population. It is known as an untreatable tumor in urgent need of new therapeutic approaches. The objective of this work was to develop multifunctional nanomedicines to treat GBM in clinical practice using combination therapy for several targets. We developed multifunctional nanopolymers (MNPs) based on a naturally derived biopolymer, poly(β-L-malic) acid, which are suitable for central nervous system (CNS) treatment. These MNPs contain several anticancer functional moieties with the capacity of crossing the blood–brain barrier (BBB), targeting GBM cells and suppressing two important molecular markers, tyrosine kinase transmembrane receptors EGFR/EGFRvIII and c-Myc nuclear transcription factor. The reproducible syntheses of MNPs where monoclonal antibodies are replaced with AP-2 peptide for effective BBB delivery were presented. The active anticancer inhibitors of mRNA/protein syntheses were Morpholino antisense oligonucleotides (AONs). Two ways of covalent AON-polymer attachments with and without disulfide bonds were explored. These MNPs bearing AONs to EGFR/EGFRvIII and c-Myc, as well as in a combination with the polymer-attached checkpoint inhibitor anti-PD-1 antibody, orchestrated a multi-pronged attack on intracranial mouse GBM to successfully block tumor growth and significantly increase survival of brain tumor-bearing animals.