ALBERT

Beschreibung: An overview is provided of time-independent physical/chemical properties as related to crystal structures. The following two points are illustrated in this review:  (1) Physical and chemical properties of structure I (sI) and structure II (sII) hydrates are well-defined; measurements have begun on sH. Properties of sI and sII are determined by the molecular structures, described by three heuristics:  (i) Mechanical properties approximate those of ice, perhaps because hydrates are 85 mol % water. Yet each volume of hydrate may contain as much as 180 volumes (STP) of the hydrate-forming species. (ii) Phase equilibrium is set by the size ratio of guest molecules within host cages, and three-phase (Lw−H−V) equilibrium pressure depends exponentially upon temperature. (iii) Heats of formation are set by the hydrogen-bonded crystals and are reasonably constant within a range of guest sizes. (2) Fundamental research challenges are (a) to routinely measure the hydrate phase (via diffraction, NMR, Raman, etc.), and (b) to formulate an acceptable model for hydrate formation kinetics. The reader may wish to investigate details of this review further, via references contained in several recent monographs.

Beschreibung: Two new iridoid glucosides, 6-O-acetylajugol (1) and 7,8-epoxy-8-epi-loganic acid (2), together with five known iridoid glucosides, galiridoside (3), ajugoside (4), 10-deoxygeniposidic acid (5), 7-deoxy-8-epi-loganic acid (6), and 8-O-acetylharpagide (7), have been isolated from the aerial parts of Leonurus persicus. Leucosceptoside A (8), eugenyl β-rutinoside (9), and kaempferol 3-O-glucoside (10) were also isolated. The structures of 1 and 2 were elucidated by extensive 1D- and 2D-NMR spectroscopy and molecular modeling. The structure of 3 was confirmed by single-crystal X-ray diffraction. Antimicrobial activity of compounds (1−10) was also evaluated against a panel of Gram-positive and Gram-negative bacteria and two strains of fungi.

Beschreibung: Six new labdane diterpenoids, leopersin C (1), 15-epi-leopersin C (2), leopersin D (3), leopersin E (4), leopersin F (5), and 7-epi-leopersin F (6) were isolated from the aerial parts of Leonurus persicus. Their structures were elucidated by extensive use of 1D and 2D homonuclear and heteronuclear shift-correlated 1H−13C-NMR spectroscopic methods. Leopersin C (1) and 15-epi-leopersin C (2) were obtained as a C-15 epimeric mixture, and their structures were elucidated on this basis.

Beschreibung: Seven new labdane diterpenoids, leopersin G−L (1−4, 6−7) and 15-epi-leopersin J (5), and two known ones, 13-hydroxyballonigrinolide (8) and ballotenol (9), were isolated from the aerial parts of Leonurus persicus along with β-sitosterol and stigmasterol. The structure determinations were mainly based on 1D and 2D NMR spectra. The stereochemical configuration of ballotenol (9) was reestablished by 2D ROESY spectroscopy and by single-crystal X-ray diffraction analysis.

Beschreibung: Test specimens of methane hydrate were grown under static conditions by combining cold, pressurized CH4 gas with H2O ice grains, then warming the system to promote the reaction CH4 (g) + 6H2O (s???l) ??? CH4??6H2O. Hydrate formation evidently occurs at the nascent ice/liquid water interface, and complete reaction was achieved by warming the system above 271.5 K and up to 289 K, at 25-30 MPa, for approximately 8 hours. The resulting material is pure methane hydrate with controlled grain size and random texture. Fabrication conditions placed the H2O ice well above its melting temperature before reaction completed, yet samples and run records showed no evidence for bulk melting of the ice grains. Control experiments using Ne, a non-hydrate-forming gas, verified that under otherwise identical conditions, the pressure reduction and latent heat associated with ice melting is easily detectable in our fabrication apparatus. These results suggest that under hydrate-forming conditions, H2O ice can persist metastably at temperatures well above its melting point. Methane hydrate samples were then tested in constant-strain-rate deformation experiments at T= 140-200 K, Pc= 50-100 MPa, and ????= 10-4-10-6 s-1. Measurements in both the brittle and ductile fields showed that methane hydrate has measurably different strength than H2O ice, and work hardens to a higher degree compared to other ices as well as to most metals and ceramics at high homologous temperatures. This work hardening may be related to a changing stoichiometry under pressure during plastic deformation; x-ray analyses showed that methane hydrate undergoes a process of solid-state disproportionation or exsolution during deformation at conditions well within its conventional stability field.

Beschreibung: We describe a new and efficient technique to grow aggregates of pure methane hydrate in quantities suitable for physical and material properties testing. Test specimens were grown under static conditions by combining cold, pressurized CH4 gas with granulated H2O ice, and then warming the reactants to promote the reaction CH4(g) + 6H2O(s→l) → CH4·6H2O (methane hydrate). Hydrate formation evidently occurs at the nascent ice/liquid water interface on ice grain surfaces, and complete reaction was achieved by warming the system above the ice melting point and up to 290 K, at 25−30 MPa, for approximately 8 h. The resulting material is pure, cohesive, polycrystalline methane hydrate with controlled grain size and random orientation. Synthesis conditions placed the H2O ice well above its melting temperature while reaction progressed, yet samples and run records showed no evidence for bulk melting of the unreacted portions of ice grains. Control experiments using Ne, a non-hydrate-forming gas, showed that under otherwise identical conditions, the pressure reduction and latent heat associated with ice melting are easily detectable in our fabrication apparatus. These results suggest that under hydrate-forming conditions, H2O ice can persist metastably to temperatures well above its ordinary melting point while reacting to form hydrate. Direct observations of the hydrate growth process in a small, high-pressure optical cell verified these conclusions and revealed additional details of the hydrate growth process. Methane hydrate samples were then tested in constant-strain-rate deformation experiments at T = 140−200 K, Pc = 50−100 MPa, and ε = 10-4−10-6 s-1. Measurements in both the brittle and ductile fields showed that methane hydrate has measurably different strength than H2O ice, and work hardens to an unusually high degree compared to other ices as well as to most metals and ceramics at high homologous temperatures. This work hardening may be related to a changing stoichiometry under pressure during plastic deformation; X-ray analyses showed that methane hydrate undergoes a process of solid-state disproportionation or exsolution during deformation at conditions well within its conventional stability field.

Beschreibung: An automated method for on-site monitoring of uranium(VI) in raffinate streams originating from nuclear fuel reprocessing plants is described. An in-line stripping procedure (based on liquid/liquid extraction) was developed to extract U(VI) from this stream, a solvent mixture of 20% tributyl phosphate and nitric acid in kerosene, into an aqueous sodium sulfate solution, Degradation products in the solvent mixture, especially dibutyl phosphate, give rise to very strong complexes and are responsible for moderate but constant U(VI) recoveries (similar to 50%), Optimal conditions for in-line stripping comprise a mixing ratio of extractant (0.5 M sodium sulfate in water)/solvent mixture of similar to 3 and a pumping rate of similar to 0.4 mL min(-1) of the solvent mixture. The determination of U(VI) was by on-line cathodic stripping voltammmetry (CSV), preceded by adsorptive collection of the U(VL) as an oxine complex onto a hanging mercury drop electrode, Quantities of 1-2 mL of the aqueous extract were pumped into the voltammmetric cell and diluted (1/5 to 1/10) with a background electrolyte containing 0.1 M PIPES buffer, 2 x 10(-4) M oxine, 10(-4) M EDTA, and 0.2 M hydrazine hydrate (pH 9.0), The CSV peak for U(VI) was obtained at -0.68 V with a detection limit of 20 nM in the raffinate stream using an adsorption time of 120 s, Both the inline stripping procedure and the on-line measurement were fully automated, with a relative standard deviation in the measurements of 〈 5%.