ALBERT

Description: The effects of different fabrication procedures to increase the damage tolerance of sandwich panels were studied. Baseline panels consisted of a 25.4 mm premolded core, surfaced with 177 C cure film adhesive and carbon-bismaleimide prepreg which were subsequently cocured onto the core. It was found that panels with a prefabricated skin, which was subsequently bonded onto the core with room temperature cure adhesive, showed greatly increased damage tolerance.

Description: The SNIP program is a FORTRAN computer code that generates NASTRAN structural model thermal loads when given SINDA (or similar thermal model) temperature results. SNIP correlates thermal nodes to structural elements to interface SINDA finite difference thermal models with NASTRAN finite element structural models. Node-to-element correlation includes determining which SINDA nodes should be related to each NASTRAN element and calculating a weighing factor for temperatures associated with each element-related thermal node. SNIP provides structural model thermal loads that accurately reflect thermal model results while reducing the time required to interface thermal and structural models as compared to other methods. SNIP uses thermal model geometry to search the three-dimensional space around each structural element for the nearest thermal nodes. Thermal model geometry is the combination of standard thermal model temperature results from SINDA and structural model geometry from NASTRAN. Thermal and structural models must both be defined in the same, single Cartesian coordinate system. The thermal nodes located nearest each element are used to determine element temperature for thermal distortion and stress analysis. The program shapes the three-dimensional search region while the user controls the size. With these region specifications, the numerical coding of thermal nodes, and the structural element numbers; the code can provide for the separation of substructures during correlation. The input to SNIP contains a file of thermal model temperature results and a physical location of each thermal node in three-dimensional space, combined in a SNIP-unique format. The input also contains a standard NASTRAN input deck for a model made up of plate, shell, beam, and bar elements. SNIP supports the CTRIA, CQUAD, CBAR, and CBEAM elements of NASTRAN. The user adjusts the input parameters in the source code which control the node-to-element correlation. The program outputs NASTRAN element temperature load cards for each element and NASTRAN case control cards for each temperature load set. SNIP also outputs a list of elements that contains the numbers of the SINDA nodes related to each NASTRAN element and the weight that is given to each node in temperature calculations. SNIP is written in ANSI standard FORTRAN 77. The PC version requires a PC FORTRAN compiler and has compiled successfully using Lahey FORTRAN v. 3.0. A core memory of 300k is recommended. The program was developed in 1987.

Description: NPLOT is an interactive computer graphics program for plotting undeformed and deformed NASTRAN finite element models (FEMs). Although there are many commercial codes already available for plotting FEMs, these have limited use due to their cost, speed, and lack of features to view BAR elements. NPLOT was specifically developed to overcome these limitations. On a vector type graphics device the two best ways to show depth are by hidden line plotting or haloed line plotting. A hidden line algorithm generates views of models with all hidden lines removed, and a haloed line algorithm displays views with aft lines broken in order to show depth while keeping the entire model visible. A haloed line algorithm is especially useful for plotting models composed of many line elements and few surface elements. The most important feature of NPLOT is its ability to create both hidden line and haloed line views accurately and much more quickly than with any other existing hidden or haloed line algorithms. NPLOT is also capable of plotting a normal wire frame view to display all lines of a model. NPLOT is able to aid in viewing all elements, but it has special features not generally available for plotting BAR elements. These features include plotting of TRUE LENGTH and NORMALIZED offset vectors and orientation vectors. Standard display operations such as rotation and perspective are possible, but different view planes such as X-Y, Y-Z, and X-Z may also be selected. Another display option is the Z-axis cut which allows a portion of the fore part of the model to be cut away to reveal details of the inside of the model. A zoom function is available to terminals with a locator (graphics cursor, joystick, etc.). The user interface of NPLOT is designed to make the program quick and easy to use. A combination of menus and commands with help menus for detailed information about each command allows experienced users greater speed and efficiency. Once a plot is on the screen the interface becomes command driven, enabling the user to manipulate the display or execute a command without having to return to the menu. NPLOT is also able to plot deformed shapes allowing it to perform post-processing. The program can read displacements, either static displacements or eigenvectors, from a MSC/NASTRAN F06 file or a UAI/NASTRAN PRT file. The displacements are written into a unformatted scratch file where they are available for rapid access when the user wishes to display a deformed shape. All subcases or mode shapes can be read in at once. Then it is easy to enable the deformed shape, to change subcases or mode shapes and to change the scale factor for subsequent plots. NPLOT is written in VAX FORTRAN for DEC VAX series computers running VMS. As distributed, the NPLOT source code makes calls to the DI3000 graphics package from Precision Visuals; however, a set of interface routines is provided to translate the DI3000 calls into Tektronix PLOT10/TCS graphics library calls so that NPLOT can use the standard Tektronix 4010 which many PC terminal emulation software programs support. NPLOT is available in VAX BACKUP format on a 9-track 1600 BPI DEC VAX BACKUP format magnetic tape (standard media) or a TK50 tape cartridge. This program was developed in 1991. DEC, VAX, VMS, and TK50 are trademarks of Digital Equipment Corporation. Tektronix, PLOT10, and TCS are trademarks of Tektronix, Inc. DI3000 is a registered trademark of Precision Visuals, Inc. NASTRAN is a registered trademark of the National Aeronautics and Space Administration. MSC/ is a trademark of MacNeal-Schwendler Corporation. UAI is a trademark of Universal Analytics, Inc.

Description: Control system experiments are described that were carried out on flexible structure facilities at the Jet Propulsion Laboratory (JPL) and the Wright-Patterson Air Force Base (WPAFB). The feedback controllers were designed using the technique of weighted gap optimization to increase structural damping and achieve robust control.

Description: The rotational stiffness of hinge joints, and the gap of the joints applied in large deployable trusses, have been experimentally shown to have a significant role in determining such structures' dynamic behavior; an analytical validation of these results is presented for the case where linear rotation springs are used to model the hinge joints employed in a simple beam in trusses. The results obtained indicate that the natural frequencies of these structures depend not only on joint stiffness but also on joint location. Such gap parameters as gap size, stiffness, position, and excitation-force levels, are discussed with a view to a deeper understanding of their effects on a space interferometry system's simulated dynamic responses.

Description: Tests were performed measuring the locations and geometries of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite/PEEK plates subjected to transverse impact loads. The data provide specific information on the effects of impactor velocity, impactor mass, material, thickness of back ply group, difference in fiber orientation between adjacent ply groups, plate thickness, and impactor nose radius. The data were compared to the results of the Finn-Springer model. The model was found to describe the data with reasonable accuracy.

Description: Microfracture (fiber/matrix fracture, interphase debonding and interply delamination) in high temperature metal matrix composites (HTMMC), subjected to thermal loading, is computationally simulated. Both unidirectional and crossply SiC/Ti15 composites are evaluated for microfracture driven by thermal loads, using multicell finite element models. Results indicate that under thermal loads alone, microfracture propagation is not as sensitive as it is under mechanical loads.

Description: This paper presents results from a finite element micromechanics analysis of thermally induced stresses in composites at cryogenic temperatures typical of spacecraft operating environments. The influence of microstructural geometry, constituent and interphase properties, and laminate orientation were investigated. Stress field results indicated that significant matrix stresses occur in composites exposed to typical spacecraft thermal excursions; these stresses varied with laminate orientation and circumferential position around the fiber. The major difference in the predicted response of unidirectional and multidirectional laminates was the presence of tensile radial stresses, at the fiber/matrix interface, in multidirectional laminates with off-axis ply angles greater than 15 deg. The predicted damage initiation temperatures and modes were in good agreement with experimental data for both low (207 GPa) and high (517 GPa) modulus carbon fiber/epoxy composites.

Description: The structural integrity of proposed high speed aircraft can be seriously affected by the extremely high surface temperatures and large temperature gradients throughout the vehicle's structure. Variations in the structure's elastic characteristics as a result of thermal effects can be observed by changes in vibration frequency, damping, and mode shape. Analysis codes that predict these changes must be correlated and verified with experimental data. The experimental modal test techniques and procedures used to conduct uniform, nonuniform, and transient thermoelastic vibration tests are presented. Experimental setup and elevated temperature instrumentation considerations are also discussed. Modal data for a 12 by 50 inch aluminum plate heated to a temperature of 475 F are presented. These data show the effect of heat on the plate's modal characteristics. The results indicated that frequency decreased, damping increased, and mode shape remained unchanged as the temperature of the plate was increased.