ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Aircraft Design, Testing and Performance  (128)
  • 1955-1959  (85)
  • 1940-1944  (43)
  • 11
    Publication Date: 2019-08-17
    Description: In an attempt to find an aerodynamic means of counteracting the transonic trim change of a fighter airplane, lower surface spoilers were tested on a 0.055-scale wind-tunnel model. The Mach number range of the tests was 0.8 to 1.2 at Reynolds numbers of approximately 4 million. Although the spoilers produced a moderate decrease in the trim change at low altitudes, they also produced a large increase in drag. Pressure-distribution tests with external fuel tanks showed large pressure changes on the lower surface of the wing due to the tanks.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-12-27-58A
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 12
    Publication Date: 2019-08-17
    Description: The Levy method which deals with an idealized structure was used to obtain the natural modes and frequencies of a large-scale built-up 45 deg. delta wing. The results from this approach, both with and without the effects of transverse shear, were compared with the results obtained experimentally and also with those calculated by the Stein-Sanders method. From these comparisons it was concluded that the method as proposed by Levy gives excellent results for thin-skin delta wings, provided that corrections are made for the effect of transverse shear.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-2-2-59L , L-153
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 13
    Publication Date: 2019-08-17
    Description: A cambered and twisted triangular wing of aspect ratio 2 in combination with a cambered body was investigated experimentally to determine the effectiveness of the camber in reducing the drag due to lift at trim at supersonic speeds. Four arrangements were tested comprising all combinations of a symmetrical and a cambered wing with a symmetrical and a cambered body. The camber shape investigated was derived by linearized lifting surface theory for triangular wings with sonic leading edges and satisfied the requirement that the wing be trimmed at the design Mach number and lift coefficient. The experimental results for the cambered wing and cambered body showed that the drag coefficient at trim was always greater, at the same lift coefficient, than that for the untrimmed symmetrical wing and body. The trim lift coefficient was positive and decreased with increasing Mach number. At the design Mach number of 2.24, the trim lift coefficient was somewhat lower and the drag coefficient was higher than values predicted by linearized lifting surface theory for the wing alone. A comparison of the trim lift-drag ratio of the cambered wing and cambered body with values obtained by trimming the symmetrical wing and symmetrical body either with a canard or a trailing-edge flap showed that, at approximately the design Mach number the cambered configuration developed a somewhat higher value than the trailing-edge flap configuration but a lower value than the canard configuration.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-2-3-59A
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 14
    Publication Date: 2019-08-17
    Description: The maximum Mach number and altitude capabilities of the Bell X-2 research airplane were achieved during a program conducted by the U.S. Air Force with Bell Aircraft Corp. providing operational support and the National Aeronautics and Space Administration providing instrumentation and advisory engineering assistance. A maximum geometric altitude of 126,200 feet was attained at a static pressure of 9.4 pounds per square foot and a dynamic pressure of 19.1 pounds per square foot. During the last flight of the airplane, a maximum Mach number of 3.20 was reached. The directionally divergent maneuver which terminated the final high Mach number flight was precipitated by the loss in directional stability that resulted from increasing the angle of attack. The yawing moment from the lateral control was sufficient to initiate the divergence and also to cause,, indirectly, rolling moments that were greater than the aileron capabilities of the airplane. The ensuing violent motions-resulting from inertial roll coupling caused the loss of the aircraft.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-TM-X-137
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 15
    Publication Date: 2019-08-16
    Description: The first flight of the North American X-15 research airplane was made on June 8, 1959. This was accomplished after completion of a series of captive flights with the X-15 attached to the B-52 carrier airplane to demonstrate the aerodynamic and systems compatibility of the X-15//B-52 combination and the X-15 subsystem operation. This flight was planned as a glide flight so that the pilot need not be concerned with the propulsion system. Discussions of the launch, low-speed maneuvering, and landing characteristics are presented, and the results are compared with predictions from preflight studies. The launch characteristics were generally satisfactory, and the X-15 vertical tail adequately cleared the B-52 wing cutout. The actual landing pattern and landing characteristics compared favorably with predictions, and the recommended landing technique of lowering the flaps and landing gear at a low altitude appears to be a satisfactory method of landing the X-15 airplane. There was a quantitative correlation between flight-measured and predicted lift-drag-ratio characteristics in the clean configuration and a qualitative correlation in the landing configuration. A longitudinal-controllability problem, which became severe in the landing configuration, was evident throughout the flight and, apparently, was aggravated by the sensitivity of the side-located control stick. In the low-to-moderate angle-of-attack range covered, the longitudinal and directional stability were indicated to be adequate.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-TM-X-195
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 16
    Publication Date: 2019-08-16
    Description: A study has been made of the subsonic pressure distributions and loadings for a 45 deg sweptback-wing and body combination at angles of attack up to 36 deg. The wing had an aspect ratio of 5.5, a taper ratio of 0.53, and NACA 64A010 sections normal to the quarter-chord line and was mounted on a slender body of fineness ratio 12.5. Test results are presented for Mach numbers of 0.30 and 0.50 with corresponding Reynolds numbers of 1.5 and 2.0 million, respectively. The stall patterns and spanwise loadings at high angles of attack for the present model are correlated with those for other 45 deg sweptback wing and body combinations having aspect ratios between 4.0 and 8.0. A tentative approach is presented for extrapolating the Weissinger span-loading method to higher angles of attack, and for deriving the spanwise-load distributions for 45 deg sweptback wings at angles of attack above 20 deg. The investigation also included tests of the body in combination with only one panel of the swept wing. The problem of estimating the normal-force coefficient for the single panel at high angles of attack is considered.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-1-18-59A
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 17
    Publication Date: 2019-08-16
    Description: Results of a cyclic load test made by NASA on an EB-47E airplane are given. The test reported on is for one of three B-47 airplanes in a test program set up by the U. S. Air Force to evaluate the effect of wing structural reinforcements on fatigue life. As a result of crack development in the upper fuselage longerons of the other two airplanes in the program, a longeron and fuselage skin modification was incorporated early in the test. Fuselage strain-gage measurements made before and after the longeron modification and wing strain-gage measurements made only after wing reinforcement are summarized. The history of crack development and repair is given in detail. Testing was terminated one sequence short of the planned end of the program with the occurrence of a major crack in the lower right wing skin.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-3-15-59L , AF-AM-171
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 18
    Publication Date: 2019-08-16
    Description: Flight tests were made to determine the capability of positioning a gliding airplane for a landing on a 5,000-foot runway with special reference to the gliding flight of a satellite vehicle of fixed configuration upon reentry into the earth's atmosphere. The lift-drag ratio and speed of the airplane in the glides were varied through as large a range as possible. The results showed a marked tendency to undershoot the runway when the lift-drag ratios were below certain values, depending upon the speed in the glide. A straight line dividing the successful approaches from the undershoots could be drawn through a lift-drag ratio of about 3 at 100 knots and through a lift-drag ratio of about 7 at 185 knots. Provision of a drag device would be very beneficial, particularly in reducing the tendency toward undershooting at the higher speeds.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-3-12-59L , L-406
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 19
    Publication Date: 2019-08-16
    Description: Several approximate procedures for calculating the bending-moment response of flexible airplanes to continuous isotropic turbulence are presented and evaluated. The modal methods (the mode-displacement and force-summation methods) and a matrix method (segmented-wing method) are considered. These approximate procedures are applied to a simplified airplane for which an exact solution to the equation of motion can be obtained. The simplified airplane consists of a uniform beam with a concentrated fuselage mass at the center. Airplane motions are limited to vertical rigid-body translation and symmetrical wing bending deflections. Output power spectra of wing bending moments based on the exact transfer-function solutions are used as a basis for the evaluation of the approximate methods. It is shown that the force-summation and the matrix methods give satisfactory accuracy and that the mode-displacement method gives unsatisfactory accuracy.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-2-18-59L , L-143
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 20
    Publication Date: 2019-08-16
    Description: A combined analytical and experimental determination is made of the coupled natural frequencies and mode shapes in the longitudinal plane of symmetry for a dynamic model of a single-rotor helicopter. The analytical phase is worked out on the basis of a seven-degree-of-freedom system combining elastic deflections of the rotor blades, rotor shaft, pylon, and fuselage. The calculated coupled frequencies are first compared with calculated uncoupled frequencies to show the general effects of coupling and then with measured coupled frequencies to determine the extent to which the coupled frequencies can be calculated. The coupled mode shapes are also calculated and were observed visually with stroboscopic lights during the tests. A comparison of the coupled and uncoupled natural frequencies shows that significant differences exist between these frequencies for some of the modes. Good agreement is obtained between the measured and calculated values for the coupled natural frequencies and mode shapes. The results show that the coupled natural frequencies and mode shapes can be determined by the analytical procedure presented herein with sufficient accuracy if the mass and stiffness distributions of the various components of the helicopter are known.
    Keywords: Aircraft Design, Testing and Performance
    Type: NASA-MEMO-11-5-58L
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...