ALBERT

Description: This paper addresses the design considerations and strategies for astrophysical observations as key elements of an international solar system exploration program. Emphasis is placed on the technical and programmatic challenges and opportunities associated with an evolving program of lunar-based astronomy. Both robotic and human tended facilities are discussed ranging from relatively small meter-class transit telescopes to large interferometer and filled-aperture systems.

Description: A method is presented by which measured modes and frequencies from a modal test can be used to determine the location and magnitude of damage in a space struss structure. The damage is located by computing the Euclidean distances between the measured mode shapes and the best achievable eigenvectors. The best achievable eigenvectors are the projection of the measured mode shapes onto the subspace defined by the refined analytical model of the structure and the measured frequencies. Loss of both stiffness and mass properties can be located and quantified. To examine the performance of the method when experimentally measured modes are employed, various damage detection studies using a laboratory eight-bay truss structure were conducted. The method performs well even though the measurement errors inevitably make the damage location more difficult.

Description: Following the project's first major design review, some unresolved technical issues, mainly centered on details of how to integrate Russian hardware into the U.S./international space station, remain. No 'show stoppers' were found in the review. Specific open technical issues are discussed in this article.

Description: A coupled, trajectory-based flowfield and material thermal-response analysis is presented for the European Space Agency proposed Rosetta comet nucleus sample return vehicle. The probe returns to earth along a hyperbolic trajectory with an entry velocity of 16.5 km/s and requires an ablative heat shield on the forebody. Combined radiative and convective ablating flowfield analyses were performed for the significant heating portion of the shallow ballistic entry trajectory. Both quasisteady ablation and fully transient analyses were performed for a heat shield composed of carbon-phenolic ablative material. Quasisteady analysis was performed using the two-dimensional axisymmetric codes RASLE and BLIMPK. Transient computational results were obtained from the one-dimensional ablation/conduction code CMA. Results are presented for heating, temperature, and ablation rate distributions over the probe forebody for various trajectory points. Comparison of transient and quasisteady results indicates that, for the heating pulse encountered by this probe, the quasisteady approach is conservative from the standpoint of predicted surface recession.

Description: Advanced Satellite for Cosmology and Astrophysics (ASCA) is a high-throughput X-ray astronomy observatory which is capable of simultaneous imaging and spectroscopic observations over a wide energy range 0.5-10 keV. The scientific capabilities of ASCA and some aspects related to its operation and observations are briefly described.

Description: We examine the electromagnetic (EM) bias by using retracked TOPEX altimeter data. In contrast to previous studies, we use a parameterization of the EM bias which does not make stringent assumptions about the form of the correction or its global behavior. We find that the most effective single parameter correction uses the altimeter-estimated wind speed but that other parameterizations, using a wave age related parameter of significant wave height, may also significantly reduce the repeat pass variance. The different corrections are compared, and their improvement of the TOPEX height variance is quantified.

Description: Monthly Ku band sigma(sub 0) and significant wave height (SWH) histograms from the NASA altimeter on the TOPEX/POSEIDON satellite are preseneted for January through June 1993 for three latitude bands between +/- 60 degrees. The data are compared to distributions from the Geosat mission for the same months in 1987-1989. Generally, the distributions agree quite well, although there are some seasonal/hemispherical differences. The sigma(sub 0) comparison reveals an overall bias between the two altimeters with the TOPEX sigma(sub 0) higher by about 0.7 dB, which is consistent with algorithm improvements for TOPEX. The SWH distributions show strong hemispherical/seasonal changes. The seasonal/hemispherical differences between TOPEX and Geosat are consistent for SWH and sigma(sub 0). The joint distribution of sigma(sub 0) and SWH is extremely stable friom month to month. The typical SWH is independent of sigma(sub 0) for sigma(sub 0) greater than 11.3 dB. The minimum SWH grows exponentially with wind speed. This joint distribution may be useful for understanding electromagnetic bias in altimeter measurements. Finally, altimeter data are compared to buoy values from 21 overflights of the NASA verification site near Pt. Conception, California. Wave heights agree well with an root mean square (RMS) difference of only 0.2 m. Altimeter sigma(sub 0) values are compared to buoy wind speeds. The results are consistent with the -0.7 dB sigma(sub 0) offset from the histogram comparisons.

Description: To assess the accuracy of the TOPEX altimeter data, we have reprocessed the raw altimeter waveform data using more sophisticated algorithms than those implemented in the altimeter hardware. We discuss systematic contamination of the waveform which we have observed and its effect on very long wavelength errors. We conclude that these systematic errors are responsible for a very long wavelength error whose peak-to-peak magnitude for the Ku band altimeter is of the order of 1 cm. We also examine the ability of retracked data to reduce the repeat pass variance and correct for significant wave height (SWH) and acceleration dependent errors. We find that the ground postprocessing contains SWH dependent biases which depend on the altimeter fine height correction.

Description: The routine ground processing of data from the NASA radar altimeter of TOPEX/POSEIDON includes instrument corrections for the effects of significant wave height and attitude angle changes on the altimeter's estimates of range, backscattered power, and significant wave height. This paper describes how these instrument corrections were generated and how they are applied. Detailed waveform fitting to telemetered waveform samples is use to assess the effectiveness of the corrections. There are several altimeter hardware-caused small waveform departures from the model waveforms and these departures, designated waveform 'features', are described in detailed. A consequence of the waveform features, and their positioning relationship to range rate, is that range data for ground tracks moving toward the equator may differ systematically by about a centimeter compared to range data for ground tracks moving away from the equator. The results and discussion are limited to side A of the redundant altimeter, as only side A has been operated on orbit.

Description: Results of the in-flight calibration and performance evaluation campaign for the TOPEX/POSEIDON microwave radiometer (TMR) are presented. Intercomparisons are made between TMR and various sources of ground truth, including ground-based microwave water vapor radiometers, radiosondes, global climatological models, special sensor microwave imager data over the Amazon rain forest, and models of clear, calm, subpolar ocean regions. After correction for preflight errors in the processing of thermal/vacuum data, relative channel offsets in the open ocean TMR brightness temperatures were noted at the approximately = 1 K level for the three TMR frequencies. Larger absolute offsets of 6-9 K over the rain forest indicated a approximately = 5% gain error in the three channel calibrations. This was corrected by adjusting the antenna pattern correction (APC) algorithm. AS 10% scale error in the TMR path delay estimates, relative to coincident radiosondes, was corrected in part by the APC adjustment and in part by a 5% modification to the value assumed for the 22.235 FGHz water vapor line strength in the path delay retrieval algorithm. After all in-flight corrections to the calibration, TMR global retrieval accuracy for the wet tropospheric range correction is estimated at 1.1 cm root mean square (RMS) with consistent peformance under clear, cloudy, and windy conditions.

Description: The NASA altimeter on board TOPEX/POSEIDON exploits the difference in the delays of the Ku and C band radar pulses to estimate an ionosphere correction to the range measurement. The dependence of the ionosphere correction on ocean and satellite parameters is less than 1 cm. The standard deviation of the 1-s averaged ionosphere correction depends on the height of the ocean waves and ranges from 5 to 14 mm. The accuracy of the ionosphere correction is better than 1 cm at the 1 sigma confidence level. The ionosphere correction should be averaged over 140 km (20 s) along track in order to minimize its noise without sacrificing its accuracy. Ionosphere models must achieve an independent sample spacing of 900 km or less in order to allow a single-frequency altimeter to have an ionosphere correction comparable in accuracy to that of the NASA dual-frequency altimeter.

Description: Estimates of the effectiveness of an altimetric correction, and interpretation of sea level variability as a response to atmospheric forcing, both depend upon assuming that residual errors in altimetric corrections are uncorrelated among themselves and with residual sea level, or knowing the correlations. Not surprisingly, many corrections are highly correlated since they involve atmospheric properties and the ocean surface's response to them. The full corrections (including their geographically varying time mean values), show correlations between electromagnetic bias (mostly the height of wind waves) and either atmospheric pressure or water vapor of -40%, and between atmospheric pressure and water vapor of 28%. In the more commonly used collinear differences (after removal of the geographically varying time mean), atmospheric pressure and wave height show a -30% correlation, atmospheric pressure and water vapor a -10% correlation, both pressure and water vapor a 7% correlation with residual sea level, and a bit surprisingly, ionospheric electron content and wave height a 15% correlation. Only the ocean tide is totally uncorrelated with other corrections or residual sea level. The effectiveness of three ionospheric corrections (TOPEX dual-frequency, a smoothed version of the TOPEX dual-frequency, and Doppler orbitography and radiopositioning integrated by satellite (DORIS) is also evaluated in terms of their reduction in variance of residual sea level. Smooth (90-200 km along-track) versions of the dual-frequency altimeter ionosphere perform best both globally and within 20 deg in latitude from the equator. The noise variance in the 1/s TOPEX inospheric samples is approximately (11 mm) squared, about the same as noise in the DORIS-based correction; however, the latter has its error over scales of order 10(exp 3) km. Within 20 deg of the equator, the DORIS-based correction adds (14 mm) squared to the residual sea level variance.

Description: The DET/MPS programs model and simulate the Direct Energy Transfer and Multimission Spacecraft Modular Power System in order to aid both in design and in analysis of orbital energy balance. Typically, the DET power system has the solar array directly to the spacecraft bus, and the central building block of MPS is the Standard Power Regulator Unit. DET/MPS allows a minute-by-minute simulation of the power system's performance as it responds to various orbital parameters, focusing its output on solar array output and battery characteristics. While this package is limited in terms of orbital mechanics, it is sufficient to calculate eclipse and solar array data for circular or non-circular orbits. DET/MPS can be adjusted to run one or sequential orbits up to about one week, simulated time. These programs have been used on a variety of Goddard Space Flight Center spacecraft projects. DET/MPS is written in FORTRAN 77 with some VAX-type extensions. Any FORTRAN 77 compiler that includes VAX extensions should be able to compile and run the program with little or no modifications. The compiler must at least support free-form (or tab-delineated) source format and 'do do-while end-do' control structures. DET/MPS is available for three platforms: GSC-13374, for DEC VAX series computers running VMS, is available in DEC VAX Backup format on a 9-track 1600 BPI tape (standard distribution) or TK50 tape cartridge; GSC-13443, for UNIX-based computers, is available on a .25 inch streaming magnetic tape cartridge in UNIX tar format; and GSC-13444, for Macintosh computers running AU/X with either the NKR FORTRAN or AbSoft MacFORTRAN II compilers, is available on a 3.5 inch 800K Macintosh format diskette. Source code and test data are supplied. The UNIX version of DET requires 90K of main memory for execution. DET/MPS was developed in 1990. A/UX and Macintosh are registered trademarks of Apple Computer, Inc. VMS, DEC VAX and TK50 are trademarks of Digital Equipment Corporation. UNIX is a registered trademark of AT&T Bell Laboratories.

Description: The DET/MPS programs model and simulate the Direct Energy Transfer and Multimission Spacecraft Modular Power System in order to aid both in design and in analysis of orbital energy balance. Typically, the DET power system has the solar array directly to the spacecraft bus, and the central building block of MPS is the Standard Power Regulator Unit. DET/MPS allows a minute-by-minute simulation of the power system's performance as it responds to various orbital parameters, focusing its output on solar array output and battery characteristics. While this package is limited in terms of orbital mechanics, it is sufficient to calculate eclipse and solar array data for circular or non-circular orbits. DET/MPS can be adjusted to run one or sequential orbits up to about one week, simulated time. These programs have been used on a variety of Goddard Space Flight Center spacecraft projects. DET/MPS is written in FORTRAN 77 with some VAX-type extensions. Any FORTRAN 77 compiler that includes VAX extensions should be able to compile and run the program with little or no modifications. The compiler must at least support free-form (or tab-delineated) source format and 'do do-while end-do' control structures. DET/MPS is available for three platforms: GSC-13374, for DEC VAX series computers running VMS, is available in DEC VAX Backup format on a 9-track 1600 BPI tape (standard distribution) or TK50 tape cartridge; GSC-13443, for UNIX-based computers, is available on a .25 inch streaming magnetic tape cartridge in UNIX tar format; and GSC-13444, for Macintosh computers running AU/X with either the NKR FORTRAN or AbSoft MacFORTRAN II compilers, is available on a 3.5 inch 800K Macintosh format diskette. Source code and test data are supplied. The UNIX version of DET requires 90K of main memory for execution. DET/MPS was developed in 1990. A/UX and Macintosh are registered trademarks of Apple Computer, Inc. VMS, DEC VAX and TK50 are trademarks of Digital Equipment Corporation. UNIX is a registered trademark of AT&T Bell Laboratories.

Description: The Flexible Spacecraft Dynamics and Control program (FSD) was developed to aid in the simulation of a large class of flexible and rigid spacecraft. FSD is extremely versatile and can be used in attitude dynamics and control analysis as well as in-orbit support of deployment and control of spacecraft. FSD has been used to analyze the in-orbit attitude performance and antenna deployment of the RAE and IMP class satellites, and the HAWKEYE, SCATHA, EXOS-B, and Dynamics Explorer flight programs. FSD is applicable to inertially-oriented spinning, earth oriented, or gravity gradient stabilized spacecraft. The spacecraft flexibility is treated in a continuous manner (instead of finite element) by employing a series of shape functions for the flexible elements. Torsion, bending, and three flexible modes can be simulated for every flexible element. FSD can handle up to ten tubular elements in an arbitrary orientation. FSD is appropriate for studies involving the active control of pointed instruments, with options for digital PID (proportional, integral, derivative) error feedback controllers and control actuators such as thrusters and momentum wheels. The input to FSD is in four parts: 1) Orbit Construction FSD calculates a Keplerian orbit with environmental effects such as drag, magnetic torque, solar pressure, thermal effects, and thruster adjustments; or the user can supply a GTDS format orbit tape for a particular satellite/time-span; 2) Control words - for options such as gravity gradient effects, control torques, and integration ranges; 3) Mathematical descriptions of spacecraft, appendages, and control systems- including element geometry, properties, attitudes, libration damping, tip mass inertia, thermal expansion, magnetic tracking, and gimbal simulation options; and 4) Desired state variables to output, i.e., geometries, bending moments, fast Fourier transform plots, gimbal rotation, filter vectors, etc. All FSD input is of free format, namelist construction. FSD is written in FORTRAN 77, PASCAL, and MACRO assembler for batch execution and has been implemented on a DEC VAX series computer operating under VMS. The PASCAL and MACRO routines (in addition to the FORTRAN program) are supplied as both source and object code, so the PASCAL compiler is not required for implementation. This program was last updated in 1985.

Description: In an effort to place payloads into orbit at the lowest possible costs, the use of air-breathing space-planes, which reduces the need to carry the propulsion system oxidizer, has been examined. As this approach would require the space-plane to fly at hypersonic speeds for periods of time much greater than that required by rockets, many factors must be considered when analyzing its benefits. The Basic Hypersonic Data and Equations spreadsheet provides data gained from three analyses of a space-plane's performance. The equations used to perform the analyses are derived from Newton's second law of physics (i.e. force equals mass times acceleration); the derivation is included. The first analysis is a parametric study of some basic factors affecting the ability of a space-plane to reach orbit. This step calculates the fraction of fuel mass to the total mass of the space-plane at takeoff. The user is able to vary the altitude, the heating value of the fuel, the orbital gravity, and orbital velocity. The second analysis calculates the thickness of a spherical fuel tank, while assuming all of the mass of the vehicle went into the tank's shell. This provides a first order analysis of how much material results from a design where the fuel represents a large portion of the total vehicle mass. In this step, the user is allowed to vary the values for gross weight, material density, and fuel density. The third analysis produces a ratio of gallons of fuel per total mass for various aircraft. It shows that the volume of fuel required by the space-plane relative to the total mass is much larger for a liquid hydrogen space-plane than any other vehicle made. This program is a spreadsheet for use on Macintosh series computers running Microsoft Excel 3.0. The standard distribution medium for this package is a 3.5 inch 800K Macintosh format diskette. Documentation is included in the price of the program. Macintosh is a registered trademark of Apple Computer, Inc. Microsoft is a registered trademark of Microsoft Corporation.

Description: The DET/MPS programs model and simulate the Direct Energy Transfer and Multimission Spacecraft Modular Power System in order to aid both in design and in analysis of orbital energy balance. Typically, the DET power system has the solar array directly to the spacecraft bus, and the central building block of MPS is the Standard Power Regulator Unit. DET/MPS allows a minute-by-minute simulation of the power system's performance as it responds to various orbital parameters, focusing its output on solar array output and battery characteristics. While this package is limited in terms of orbital mechanics, it is sufficient to calculate eclipse and solar array data for circular or non-circular orbits. DET/MPS can be adjusted to run one or sequential orbits up to about one week, simulated time. These programs have been used on a variety of Goddard Space Flight Center spacecraft projects. DET/MPS is written in FORTRAN 77 with some VAX-type extensions. Any FORTRAN 77 compiler that includes VAX extensions should be able to compile and run the program with little or no modifications. The compiler must at least support free-form (or tab-delineated) source format and 'do do-while end-do' control structures. DET/MPS is available for three platforms: GSC-13374, for DEC VAX series computers running VMS, is available in DEC VAX Backup format on a 9-track 1600 BPI tape (standard distribution) or TK50 tape cartridge; GSC-13443, for UNIX-based computers, is available on a .25 inch streaming magnetic tape cartridge in UNIX tar format; and GSC-13444, for Macintosh computers running AU/X with either the NKR FORTRAN or AbSoft MacFORTRAN II compilers, is available on a 3.5 inch 800K Macintosh format diskette. Source code and test data are supplied. The UNIX version of DET requires 90K of main memory for execution. DET/MPS was developed in 1990. A/UX and Macintosh are registered trademarks of Apple Computer, Inc. VMS, DEC VAX and TK50 are trademarks of Digital Equipment Corporation. UNIX is a registered trademark of AT&T Bell Laboratories.

Description: NASA-JPL's four-frequency telecommunication system design entails the creation and integration of a frequency-selective surface (FSS) subreflector into the high-gain antenna subsystem. The FSS design, which incorporates a periodic array of conducting elements on a kevlar/polymer composite structure, will be able to multiplex S, X, Ku, and Ka frequency-band wavelengths. Accounts are presented of the FSS's development, mechanical testing, and electrical testing.

Description: Technology is being developed to process signals from distributed sensors using distributed computations. These distributed sensors provide a new feedback capability for vibration control that has not been exploited. Additionally, the sensors proposed are of an optical and distributed nature and could be employed with known techniques of distributed optical computation (Fourier optics, etc.) to accomplish the control system functions of filtering and regulation in a distributed computer. This paper reviews a procedure for the analytic design of control systems for this application. For illustration, the procedure is applied to the problem of suppressing the vibrations of a simply supported beam. A simulator has been developed to study the effects of sensor and processing errors. An extensive study of the effects of these errors on estimation and regulation performance is presented.

Description: The Task Committee on Methods for Identification of Large Structures in Space was founded in Jul. 1984. The charter of the committee was to prepare a state-of-the-art report on methods of system identification applicable to large space structures (LSS). Funding to support preparation of the report was received in Aug. 1985 from the Air Force Rocket Propulsion Laboratory (now the Air Force Astronautics Laboratory), in the form of a contract to the ASCE. The report was completed, and published by AFRPL in Sep. 1986. The Task Committee consisted of ten members, including ASCE and AFRPL representatives. The membership represented Government, Industry, and Universities, and consisted of electrical, mechanical, and civil engineers, with backgrounds in Structural Dynamics, Optimization, and Controls. An effort was made to use consistent terminology and notation throughout the report which would be compatible with the terminology used in both the structures and controls communities.

Description: This paper describes an autonomous control concept for pointing and articulation of science instruments on the Eos (Earth observing system) NASA/NOAA platforms intended to be operational by the late 1990s. Key features of this concept include advanced control adaptation and tuning strategies which provide performance robustness over a wide range of system uncertainties and mission time criticality. System identification-control modification paradigms are synthesized to form an adaptation continuum over this extended regime of autonomous operations.

Description: Large space structures are characterized by a large number of modes, grouped frequencies, and small inherent damping. Model reduction techniques in time domain may not be effective due to small damping. The model truncation method is generally used. This method can not solve the problem of grouped frequencies, and will lose all the information about the higher order modes. A new method developed in this paper, which tries to minimize the error of interested transfer functions, makes use of all the information of the original system, and achieves improvement not only from a smaller error of transfer functions but also from better frequency distribution.

Description: A space flight experiment being developed by NASA's Office of Aeronautics and Space Technology (OAST) that uses the Space Station as a testbed to study techniques for determining the dynamic characteristics of large space structures (LSS) is described. The experiment is separate from the Space Station Program itself with research objectives outside the domain of Space Station Program objectives. A brief description of the experiment, in terms of the general objective and approach, is given along with a statement of the potential benefits to NASA and others. The bulk of material to follow deals with the experiment definition activity that is underway. The scope of an 'initial' definition study and preliminary results from supporting Space Station dynamics analyses is presented. The term initial is used to indicate that the study currently being conducted has limited objectives and is not expected to complete the required experiment definition. A follow on study is planned and is mentioned in the summary.

Description: A reanalysis of the evolution configuration module pattern for Space Station Freedom is presented. The module pattern is to consist of one habitation module, one airlock, one cupola, two Space Shuttle Orbiter pressurized docking adapters, one assured crew return vehicle, and one pressurized logistics module. Three laboratory modules are also included. A phased plan has been developed on the basis of utilization analysis being performed and derived through actual and projected user mission requirements for the growth of pressurized elements. The evolution requirement impacts to the module pattern are outlined. Application of the growth philosophy and the physical limitations resulted in a number of core element ground rules for module pattern growth. Nodes and modules are to be grown symmetrically in order to optimize poor flight control characteristics and maximize the capability for crew dual egress between elements. Core module pattern elements are not to be grown along Y-Y axis from nodes 1 or 2 due to physical clearance problems with the thermal control system radiators operational envelope.

Description: Results are presented of a thermal design optimization study of the segmented GFRP primary reflector of the earth-orbiting Submillimeter Imager and Line Survey telescope. The paper examines the thermal requirements of the primary reflector and the thermal environment of the telescope and describes the thermal design of the primary reflector. Particular attention is given to the geometric math model and the thermal math model of the telescope. A summary for the steady-state thermal performance of the optimized design is presented, showing that the optimized design has reduced, by an order of magnitude, structural spatial temperature gradients, which were earlier shown to be the most significant obstacle in maintaining the required telescope figure accuracy.

Description: The research experience of SCOLE developed by the NASA Langley Research Center is reviewed. Particular attention is given to the advances made in control and modeling techniques, the experimental facilities that are now available, and the continuing needs to advance and to validate the technologies in controlling flexible structures.

Description: An analytic redundancy management approach for on-line component failure detection is described and illustrated using a simulation of the NASA Langley Spacecaft Control Laboratory Experiment (SCOLE) research facility. The SCOLE experimental apparatus simulated is a functional model of the Space Shuttle with a large, flexible, offset-feed antenna cantilevered from the payload bay. This approach uses a single, active, Kalman filter selected from a bank of filters, each element of which was previously designed to accommodate a specific failure condition. The residuals of this active filter are processed through a sequential probability ratio test (SPRT) filter to identify the failure state of the system and, hence, closing the failure accommodation loop, to select the active filter. Results are presented that illustrate the ability of the system to detect and recover from failures introduced in the angular rate and linear acceleration sensors on the SCOLE facility.

Description: One of the basic requirements in engineering analysis is the development of a mathematical model describing the system. Frequently comparisons with test data are used as a measurement of the adequacy of the model. An attempt is typically made to update or improve the model to provide a test verified analysis tool. System identification provides a systematic procedure for accomplishing this task. The terms system identification, parameter estimation, and model correlation all refer to techniques that use test information to update or verify mathematical models. The goal of system identification is to improve the correlation of model predictions with measured test data, and produce accurate, predictive models. For nonmetallic structures the modeling task is often difficult due to uncertainties in the elastic constants. A finite element model of the shell was created, which included uncertain orthotropic elastic constants. A modal survey test was then performed on the shell. The resulting modal data, along with the finite element model of the shell, were used in a Bayes estimation algorithm. This permitted the use of covariance matrices to weight the confidence in the initial parameter values as well as confidence in the measured test data. The estimation procedure also employed the concept of successive linearization to obtain an approximate solution to the original nonlinear estimation problem.

Description: Reliable structural dynamic models will be required as a basis for deriving the reduced-order plant models used in control systems for large space structures. Ground vibration testing and model verification will play an important role in the development of these models; however, fundamental differences between the space environment and earth environment, as well as variations in structural properties due to as-built conditions, will make on-orbit identification essential. The efficiency, and perhaps even the success, of on-orbit identification will depend on having a valid model of the structure. It is envisioned that the identification process will primarily involve parametric methods. Given a correct model, a variety of estimation algorithms may be used to estimate parameter values. This paper explores the effects of modeling errors and model deficiencies on parameter estimation by reviewing previous case histories. The effects depend at least to some extent on the estimation algorithm being used. Bayesian estimation was used in the case histories presented here. It is therefore conceivable that the behavior of an estimation algorithm might be useful in detecting and possibly even diagnosing deficiencies. In practice, the task is complicated by the presence of systematic errors in experimental procedures and data processing and in the use of the estimation procedures themselves.

Description: On-orbit system identification (ID) of large space systems is essential for various reasons. For example, the complex composite structure of such systems cannot be ground-tested; their structural dynamic characteristics must be known accurately in order to accomplish active control. Furthermore, such capability can be used to characterize/identify various disturbances. The identification process is consisted of four principal elements: (1) modeling, (2) the estimation algorithm, (3) input system, and (4) measurement system. These elements are highly correlated and all togerher determine the success of the identification problem. Accurate modeling of large space systems is the most important element of the identification process. Large flexible structures are non-linear and infinite dimensional systems with highly coupled parameters and low frequency packed modes. In addition, these systems are subject to stochastic and time-varying disturbances, they have structural parameters which can vary due to on-orbit assembly deployment, and operations. These systems are generally; however, represented by constant coefficient, finite order differential equations. The non-linearities, coupling and noise effects are also often neglected. Moreover, identification experiment designs which lead to highly complex optimization problems usually require the simultaneous choice of ID algorithm, sensor, and actuator type and placement. On-orbit bandwidth and power restrictions on excitation, limited data window, and restrictions on sensor/actuator type, placement and number, has led to practical questions of implementations.

Description: This paper examines the use of on-orbit identification based on Maximum Likelihood Estimation (MLE) to provide these high-order, high-accuracy control design models for large space structures (LSS's). First, it outlines a general MLE identification algorithm, together with a covariance-analysis procedure to assess algorithm performance in terms of systematic and stochastic errors. Next, it examines various simplifications appropriate for the LSS identification application. Simplified analytical performance results are presented, as are numerical results to support these analyses. Finally, a graphical interpretation of these results is given.

Description: This talk focuses on the determination of state-space models for large space systems using only the output data. The output data could be generated by the unknown or deliberate initial conditions of the space structure in question. We shall review some relevant fundamental work on the state-space modeling of sequential output data that is potentially applicable to large space structures. If formulated in terms of some generalized Markov parameters, this approach is in some sense similar to, but much simpler than, the Juang-Pappa Eigensystem Realization Algorithm (ERA) and the Ho-Kalman construction procedure.

Description: For the future space systems, on-orbit identification (ID) capability will be required to complement on-orbit control, due to the fact that the dynamics of large space structures, spacecrafts, and antennas will not be known sufficiently from ground modeling and testing. The computational requirements for ID of flexible structures such as the space station (SS) or the large deployable reflectors (LDR) are however, extensive due to the large number of modes, sensors, and actuators. For these systems the ID algorithm operations need not be computed in real-time, only in near real-time, or an appropriate mission time. Consequently the space systems will need advanced processors and efficient parallel processing algorithm design and architectures to implement the identification algorithms in near real-time. The MAX computer currently being developed may handle such computational requirements. The purpose is to specify the on-board computational requirements for dynamic and static identification for large space structures. The computational requirements for six ID algorithms are presented in the context of three examples: the JPL/AFAL ground antenna facility, the space station (SS), and the large deployable reflector (LDR).

Description: This proposal discusses a new nonlinear, nonparametric method for off-line modeling and on-line estimation of the deformation of a flexible structure undergoing rapid retargeting maneuvers. In these circumstances, the structural stiffness and damping coefficients depend on the angular acceleration omega(dot), the angular rate omega, and the square of the angular rate omega. In the single axis case, the excitation of the structure is represented by the vector u(exp T) = (omega(dot), omega(exp 2), 2(omega)), to which the structural dynamics responds as a 'bilinear' (i.e., parametrically excited) system. A similar technique for multiaxial rotations yields a bilinear model with respect to matrix valued excitations. Three methods of estimation and modeling are described in this proposal to achieve deformation state determination: (1) a method based on a feedback linearized procedure which gives an estimate of the state by means of observers installed in the deformable body; (2) off-line modeling of the deformation state of the structure by means of topological interpolators; and (3) an on-line structural state estimation method based on a combination of the two previous techniques.

Description: Viewgraphs on current analytical gaps for future needs for large space systems are presented. Topics covered include: future spacecraft; common control objectives; accuracy requirements; increasing complexity; promising approaches; and analytical gaps.

Description: Structural sizing and performance data are presented for two different aerobrake hexagonal heatshield panel structural concepts. One concept features a sandwich construction with an aluminum honeycomb core and thin quasi-isotropic graphite-epoxy face sheets. The other concept features a skin-rib isogrid construction with thin quasi-isotropic graphite-epoxy skins, and graphite-epoxy ribs oriented at 0, +60, and -60 deg along the panel. Linear static, linear bifurcation buckling, and nonlinear static analyses were performed to compare the structural performance of the two panel concepts and assess their feasibility for a Lunar Transfer Vehicle aerobrake application.

Description: An effort is currently being carried out by the Jet Propulsion Laboratory (JPL) to study mission feasibility and to define functional requirements for various subsystems of the Space Infrared Telescope Facility (SIRTF). As a major part of this effort, structural design requirements have been derived based on the stated mission objectives. Design concerns addressed by these requirements include the limits on mass and location of the center of gravity, launch stiffness and dynamic characteristics, design loads and analysis criteria, survivability of the TITAN IV/Centaur launch environment, thermal control for maintaining a near absolute-zero operating temperature, and helium cryogen volume and storage for a five-year mission. To illustrate how the structural design requirements can be met, a point design of the SIRTF flight hardware system was developed, modeled, and analyzed. A description of the key features of this point design, along with pertinent modeling and analysis results, are discussed in this Paper.

Description: The progress in spacecraft charging is reviewed with particular attention given to the interactions of plasma and penetrating radiation with dielectrics. Topics discussed include the charging environments, elementary charging theory, the anomalies attributed to charging or discharging phenomena, and spacecraft engineering.

Description: The objectives of the Solar Probe mission and the current status of the Solar Probe thermal shield subsystem development are described. In particular, the discussion includes a brief description of the mission concepts, spacecraft configuration and shield concept, material selection criteria, and the required material testing to provide a database to support the development of the shield system.

Description: Arcjet thrusters are soon to be used for north/south stationkeeping on commercial communications satellites. A series of tests was performed to evaluate the possible effects of these thrusters on spacecraft charging and the degradation of thermal control material. During the tests the interaction between arcjet plumes and both charged and uncharged surfaces did not cause any significant material degradation. In addition, firing an arcjet thruster benignly reduced the potential of charged surfaces to near zero.

Description: The present multidisciplinary telescope-analysis approach, which encompasses thermal, structural, control and optical considerations, is illustrated for the case of an IR telescope in LEO; attention is given to end-to-end evaluations of the effects of mechanical disturbances and thermal gradients in measures of optical performance. Both geometric ray-tracing and surface-to-surface diffraction approximations are used in the telescope's optical model. Also noted is the role played by NASA-JPL's Integrated Modeling of Advanced Optical Systems computation tool, in view of numerical samples.

Description: In this paper a distributed parameter model for the estimation of modal characteristics of NASA Mini-Mast truss is proposed. A closed-form solution of the Timoshenko beam equation, for a uniform cantilevered beam with two concentrated masses, is derived so that the procedure and the computational effort for the estimation of modal characteristics are improved. A maximum likelihood estimator for the Timoshenko beam model is also developed. The resulting estimates from test data by using Timoshenko beam model are found to be comparable to those derived from other approaches.

Description: Parameter identification and modeling are key elements of a design and operational flight strategy for control of flexible space structures. The emphasis of the identification program is on on-orbit applications to spacecraft control. High performance robust controllers will result from advanced design synthesis techniques and on-orbit identification/system tuning. Near term goals for the program include development of an integrated on-line processing capability for flexible body parameter identification, and validation with physical structure experiments.

Description: Viewgraphs and discussion on on-orbit system parameter identification are included. Topics covered include: dynamic programming filter (DPF); cost function and estimator; frequency domain formulation structrual dynamic identification; and attributes of DPF.

Description: On-going research at The Aerospace Corporation studying the feasibility of applying adaptive control methodologies to the control of flexible space structures is described. A laboratory testbed was established to test system identification and control approaches. The laboratory set-up and controller design approach are discussed. The ARX least squares parameter estimation technique is analyzed in terms of frequency domain transfer function bias error. This analysis approach enables the determination of the effects of sampling rate, sensor type, and data prefiltering on the estimation performance. The ability to identify space structure dynamics over a range of frequencies is shown to be heavily dependent on these factors.

Description: Accurate mathematical models are clearly an important part of the design, modification, control, and damage assessment of large space structures. A critical part of model determination of any type of structure is the use of system identification (SI), a process for using measured excitation and response data to improve the form of a mathematical model or the values of the parameters in it. The reasons for using SI are manifold, but most of them involve uncertainties in either the form of or the parameters in the mathematical model. Some of the more common uncertainties are the following: the nature of the damping, the characteristics of sloppy or sticky joints, inelastic material properties, and parameters in a reduced Degree-of-Freedom (DOF) model. This paper contains a description of the SI algorithm followed by two illustrations: one in which all parameters in a shear building model are determined using pull back and quick release data, and another in which an equivalent reduced DOF model is obtained for a two story frame.

Description: This presentation will address an approach for using modal residues and roots, typically derived from vibration testing, to solve for the lumped parameters of a finite element model. The uniqueness of the approach is that the mass, stiffness, or damping matrices of a structure do not need to be known or estimated a-priori. Instead just the connectivity of the structure needs to be estimated. In addition, the presentation will demonstrate how models with orders larger than the number of modes obtained by the test program can be solved. The presentation will start by covering the basis of the approach, then illustrate a trivial application of how it works, and finally illustrate its use on a cantilevered beam using only a fraction of the mode to solve the mass, stiffness, and damping matrices.

Description: Virtually all space structure mission requirements include control of vibration, position, and possibly shape. In order to satisfy their requirements it is necessary to know the dynamic characteristics of the structure. Therefore, a means must be developed to continuously determine a dynamic model, or changes in the model, and to appropriately adapt the controls to these changes. The detection and location of physical damage would also be a very beneficial characteristic of such a procedure. A discussion outlining the methods to perform On-Orbit Model Determination is presented.

Description: For the past several years much effort has been given to the development of techniques for designing control systems for large space structures (LSS's). The main objective of these efforts has been to develop a LSS control methodology that produces designs that meet strenuous performance requirements and are robust to model inaccuracies. Unfortunately, performance and robustness are conflicting requirements. Because LSS's can not be fully tested on ground, it has become an accepted fact that the design of LSS control systems to meet performance requirements can not be completed until the LSS is placed on-orbit and tested and an accurate model is extracted from on-orbit test results. Modern MIMO sampled-data frequency response design techniques are viable candidates for designing LSS control systems. First, this paper presents techniques for performing MIMO system identification (ID) from test data. Then, techniques for improving the performance of the system ID process in the presence of noise are presented. Finally, practical utility of the system ID approaches are validated by the presentation of results obtained from application on the LSS Ground Test Facility at Marshall Space Flight Center.

Description: The Galileo scan platform is controlled in two degrees of freedom. A clock (Spin Bearing) actuator controls the relative position between the rotor and stator, and a cone actuator controls the position between the stator and the platform. Instruments on the platform are required to point to 140 micro-rad accuracy and 50 micro-rad per second stability. The system identification objectives were to identify dominant structural resonance frequencies, mode shapes, and damping ratio which exist in the transfer function between the clock actuator and the gyro sensor; and position the notch filter to limit undesirable actuator torque output to ensure stability and performance.

Description: Many modern spacecraft are complex multi-body dynamic systems where the bodies are connected by several active control systems for pointing and isolation. Mission requirements indicate that many structural modes and possibly some nonlinear effects will require characterization. Thus, even characterization at the subsystem level will become more difficult than usual. System level characterization difficulties will be compounded by the fact that only limited ground testing will be possible on the full up system, and flight testing will be restricted by an extremely limited measurements set. The object of the present discussion is the application of matrix majorant theory to the problem of assessing dynamic system performance when knowledge of the system is uncertain. We show how majorants provide an effective tool to relate required performance output to system identification test quality in terms of residual uncertainty in input-output relations, parameter values, nonlinearities, and interactions. The underlying machinery consists of the block-norm matrix which is a nonnegative matrix each of whose elements is the norm of a block of a suitably partitioned matrix. A matrix which bounds the block-norm matrix in the sense of nonnegative matrices, i.e., element by element is known as a majorant.

Description: An optimal on-orbit experiment is designed to extract the most information from an on-orbit test, subject to the constraints of the testing environment. However, simply jumping in and optimizing standard measures of information with respect to the experiment design can cause severe problems if attention is not paid to the specific needs and properties of the problem at hand. The actual criteria to be optimized depends on (among other things) the particular ID algorithm and parametrization being used. Two parametric techniques are the focus of this presentation: recursive prediction error method (RPEM) and maximum likelihood estimation (MLE).

Description: The research project which resulted in the AMI (Analytical Model Improvement) method was funded by the Langley Research Center from 1979 through 1985. The objective was to develop a method for obtaining improved dynamic models of structures by using both test data and numerical analysis. The research was successfully performed and the method was applied to a real structure having a realistic NASTRAN model with over 500 degrees of freedom. The method and its application are briefly discussed as well as other indirect benefits in related technical areas.

Description: The objective of this paper is to summarize and review several investigations on the assessment and control of structural damage in civil engineering. Specifically, the definition of structural damage is discussed. A candidate method for the evaluation of damage is then reviewed and demonstrated. Various ways of implementing passive and active control of civil engineering structures are next summarized. Finally, the possibility of applying expert systems is discussed.

Description: An eigenvector expansion method is utilized to predict eigenvalue and eigenvector derivatives due to geometric reconfiguration of a Gimbalflex fine-pointing/vibration isolation system called SAVI (Space Active Vibration Isolation). The eigenvector expansion method used is a modification of the classical method and allows for rigid body roots. Using the resulting modal derivatives, free-free nonlinear equations of motion are developed with Lagrange's Method. These equations represent a nonlinear plant model to be used in conjunction with a control system transient response simulation.

Description: Two different methods are proposed for identifying the structural properties of large orbiting space structures under ordinary service loads, and for assessing potential damage due to impact or other extreme loadings. It is shown that the behavior of a structure in a weightless environment is nonlinear due to unloaded or lightly loaded connections, an effect which not only complicates structural control, but makes the problem of system identification more difficult than for ground based systems. Both proposed methods assume that the structure is subjected to loads imposed by prescribed self stressing systems sufficient to produce repeatable internal force systems in the structure. The first method is based on statical response and requires a survey of structural displacements produced by the self stressing systems. The displacements do not have to be determined completely (i.e., in three directions at each connection), but more displacement information produces more accurate structural stiffness information. It is anticipated that displacement measurements will be taken using on-board laser measurement devices. The second technique employs dynamic stress wave measurement techniques using on-board loading devices and strain gages to track stress wave propagation through the space structure. This approach, which is in its early stages of development, relies on an analysis of transit times of impulsive stress waves and changes in transit times and wave forms due to changes in structural parameters.

Description: Uncertainties of a large space system (LSS) can be deterministic or stochastic in nature. The former may result in, for example, an energy spillover problem by which the interaction between unmodeled modes and controls may cause system instability. The stochastic uncertainties are responsible for mode localization and estimation errors, etc. We will address the effects of uncertainties on structural model formulation, use of available test data to verify and modify analytical models before orbiting, and how the system model can be further improved in the on-orbit environment.

Description: A time-optimal open-loop control problem of flexible spacecraft in the presence of modeling uncertainty has been investigated. The results indicate that the proposed approach significantly reduces the residual structural vibrations caused by modeling uncertainty. The results also indicate the importance of proper jet placement for practical tradeoffs among the maneuvering time, fuel consumption, and performance robustness.

Description: This paper uses spatial operator techniques to develop a new algorithm for the dynamics of multibody systems with hinges undergoing prescribed motion. This algorithm is spatially recursive, and its computational complexity grows only linearly with the number of degrees of freedom in the system. Its structure is a hybrid of known recursive forward and inverse dynamics algorithms for regular multibody systems. Changes to the prescribed/nonprescribed nature of hinges can be implemented during run time since they are handled with very low overhead in the algorithm.

Description: The evolution and optimization of a real-time digital control system is presented. The control system is part of a testbed used to perform focused technology research on the interactions of spacecraft platform and instrument controllers with the flexible-body dynamics of the platform and platform appendages. The control system consists of Computer Automated Measurement and Control (CAMAC) standard data acquisition equipment interfaced to a workstation computer. The goal of this work is to optimize the control system's performance to support controls research using controllers with up to 50 states and frame rates above 200 Hz. The original system could support a 16-state controller operating at a rate of 150 Hz. By using simple yet effective software improvements, Input/Output (I/O) latencies and contention problems are reduced or eliminated in the control system. The final configuration can support a 16-state controller operating at 475 Hz. Effectively the control system's performance was increased by a factor of 3.

Description: One of the main difficulties encountered in the design and implementation of control systems for spacecraft is the interaction between the control system and the flexibility of the vehicle. This difficulty has resulted in problems for a multitude of spacecraft including the earliest U.S. spacecraft, Explorer I; the Orbiting Geophysical Observatory III; Mariner 10; Galileo; and the Hubble Telescope. Recognizing the importance of the issue, NASA has an ongoing Controls-Structures Interaction (CSI) technology program to develop the methodology to design optimally and simultaneously both the control system and the structure. The CSI program is a multicenter program involving research teams from NASA's Langley Research Center (LaRC), Jet Propulsion Laboratory (JPL), and Marshall Space Flight Center (MSFC). JPL's area of interest is in optics-class vehicles and MSFC's in astrophysics vehicles. The aim of this paper is to explain the ongoing activities at LaRC, which are of a theoretical, ground test, and flight test nature, with focus on applications to spacecraft with multiple experiment-pointing mounts, large space radiometers, Space Station Freedom (SSF), and the Space Shuttle Remote Manipulator System (RMS).

Description: A critical technology area for lightweight SiC-based telescope systems is the structural integrity and thermal stability over spaceborne environmental launch and thermal operating conditions. Note, it is highly desirable to have an inherently athermal design of both SiC mirrors and structure. SSG has developed an 8 inch diameter SiC telescope system for brassboard level optical and thermal testing. The brassboard telescope has demonstrated less than 0.2 waves P-V in the visible wavefront change over +50 C to -200 C temperature range. SSG has also fabricated a SiC truss structural assembly and successfully qualified this hardware at environmental levels greater than 3 times higher than normal Delta, Titan, and ARIES launch loads. SSG is currently developing two SiC telescopes; an 20 cm diameter off-axis 3 mirror re-imaging and a 60 cm aperture on-axis 3 mirror re-imager. Both hardware developments will be tested to flight level environmental, optical, and thermal specifications.

Description: The objective of this project is to identify modal properties such as the eigenvalues and eigenfunctions of structures. The formal means for accomplishing this task, Structural Identification, is viewed as a two step procedure: (1) identify the eigensolution; and (2) using the identified eigensolution, identify the mass and stiffness. The eigensolution is identified as a correction on a postulated model based on erroneous parameters.

Description: The topics are presented in viewgraph form and include the following: directed energy systems - vibration issue; Neutral Particle Beam Integrated Space Experiment (NPB-ISE) opportunity/study objective; vibration sources/study plan; NPB-ISE spacecraft configuration; baseline slew analysis and results; modal contributions; fundamental pitch mode; vibration reduction approaches; peak residual vibration; NPB-ISE spacecraft slew experiment; goodbye ISE - hello Zenith Star Program.

Description: The Vibroacoustic Payload Environment Prediction System (VAPEPS) was used to predict the stationary on-orbit environments in one of the Space Station Freedom modules. The model of the module included the outer structure, equipment and payload racks, avionics, and cabin air and duct systems. Acoustic and vibratory outputs of various source classes were derived and input to the model. Initial results of analyses, performed in one-third octave frequency bands from 10 to 10,000 Hz, show that both the microgravity and acoustic environments will be exceeded in some one-third octave bands with the current SSF design. Further analyses indicate that interior acoustic level requirements will be exceeded even if the microgravity requirements are met.

Description: In this article, the vibration control of adaptive truss structures, where the control actuation is provided by length adjustable active members, is formulated as a direct output feedback control problem. A control method named Model Truncated Output Feedback (MTOF) is presented. The method allows the control feedback gain to be determined in a decoupled and truncated modal space in which only the critical vibration modes are retained. The on-board computation required by MTOF is minimal; thus, the method is favorable for the applications of vibration control of large scale structures. The truncation of the modal space inevitably introduces spillover effect during the control process. In this article, the effect is quantified in terms of active member locations, and it is shown that the optimal placement of active members, which minimizes the spillover effect (and thus, maximizes the control performance) can be sought. The problem of optimally selecting the locations of active members is also treated.

Description: Future NASA missions such as the Great Observatories of the 21st Century, will require high dimensional stability (i.e., the system's ability to retain geometrical properties related to the system's performance) which will have to be maintained with micron to nanometer accuracy over the 5 to 10 years of mission lifetime. This paper examines the thermodynamic and other mechanisms which limit the dimensional stability of a space system. It is shown that the space system's performance will be limited below 0.1 per million dimensional stability.

Description: This paper describes a preliminary design of the thrust vector control algorithm for the interplanetary spacecraft, Cassini. Topics of discussion include flight software architecture, modeling of sensors, actuators, and vehicle dynamics, and controller design and analysis via classical methods. Special attention is paid to potential interactions with structural flexibilities and propellant dynamics. Controller performance is evaluated in a simulation environment built around a multi-body dynamics model, which contains nonlinear models of the relevant hardware and preliminary versions of supporting attitude determination and control functions.

Description: Imaging the Earth's magnetosphere from space will enable scientists to better understand the global shape of the inner magnetosphere, its components and processes. The proposed Inner Magnetosphere Imager (IMI) mission will obtain the first simultaneous images of the component regions of the inner magnetosphere and will enable scientists to relate these global images to internal and external influences as well as local observations. NASA's Marshall Space Flight Center (MSFC) is performing a concept definition study of the proposed mission. As currently envisioned, the baseline mission calls for an instrument complement of approximately seven imagers to be flown in an elliptical Earth orbit with an apogee of seven Earth Radii (RE). Several spacecraft concepts have been examined for the mission. The baseline concept utilizes a spinning spacecraft with a despun platform, the second uses a three-axis stabilized spacecraft with a spinning platform, while the third option splits the instruments onto two small satellites; a spinning spacecraft and a complementary three-axis stabilized spacecraft. This paper will address the mission objectives, the rationale for using proven spacecraft designs, and the preliminary concept definition study team results for all three options.

Description: An effort was made to increase the predicted lifetime of the SIRTF dewar by lowering the exterior shell temperature, increasing the radiated energy from the vapor cooled shields and reconfiguring the vapor cooled shields. The lifetime increases can be used to increase the scientific return from the mission and as a trade-off against mass and cost. This paper describes the configurations studied, the steady state thermal model used, the analytical methods and the results of the analysis. Much of the heat input to the outside dewar shell is radiative heat transfer from the solar panel. To lower the shell temperature, radiative cooled shields were placed between the solar panel and the dewar shell and between the bus and the dewar shell. Analysis showed that placing a radiator on the outer vapor cooled shield had a significant effect on lifetime. Lengthening the distance between the outer shell and the point where the vapor cooled shields are attached to the support straps also improved lifetime.

Description: A control law for a single-tether orbiting satellite system based on a reduced order linear adaptive control technique is presented. The main advantages of this technique are its design simplicity and the facts that specific system parameters and model linearization are not required when designing the controller. Two controllers are developed: one which uses only tension in the tether as control actuation and one which uses both tension and in-plane thrusters as control actuation. Both a sixth-order nonlinear and an 11th-order bead model of a tethered satellite system are used for simulation purposes, demonstrating the ability of the controller to manage an uncertain system. Retrieval and stationkeeping results using these nonlinear models and the linear adaptive controller demonstrate the feasibility of the method. The robustness of the controller with respect to parameter uncertainties is also demonstrated by changing the nonlinear model and parameters within the model without redesigning the controller.

Description: The glowing cloud near the ram surfaces of the Space Shuttle was observed with a hand-held, intensified spectrograph operated by the astronauts from the aft-flight-deck of the Space Shuttle. The spectral measurements were made between 400 and 800 nm with a resolution of 3 nm. Analysis of the spectral response of the instrument and the transmission of the Shuttle window was performed on orbit using earth-airglow OH Meinel bands. This analysis resulted in a correction of the Shuttle glow intensity in the spectral region between 700 and 800 nm. The data presented in this report is in better agreement with laboratory measurements of the NO2 continuum.

Description: Recent laboratory results using a refined phase resonance method and the eigensystem realization algorithm on the same test structure are reported. These methods are dissimilar modal identification techniques suitable for future large spacecraft. The theory, application approach, and results obtained for each technique are summarized and compared. Although both methods worked well in this investigation, significant differences occurred in some identified mode shapes. Comparison of independently derived modal parameters provides the means for disclosing such discrepancies in flight projects.

Description: This paper discusses practical aspects of performing on-orbit modal identification using time domain analysis of free-decay data. The effects of environmental constraints, structural characteristics, excitation, and sensing are reviewed. In a recent laboratory application, an on-orbit experiment is simulated using a limited number of excitation and measurement points. The identified modal parameters correlate well, though not uniquely, with those obtained in a complete modal survey. Practical difficulties in performing the correlation are illustrated.

Description: The potential benefits of employing controlled structures technology in spacecraft design are illustrated using an example of a Mission-to-Planet Earth multisensor geostationary platform. The platform has a precipitation mapping sensor which requires large antennas to meet the science requirement of resolution cell size and dynamic measurement range. A series approach and an integrated approach to designing a controlled structure are discussed.

Description: Major issues in system identification are summarized and recent advances are reviewed. Modal testing and system identification used in control theory are examined, and the mathematical relationships and conversions of the models appropriate to modal testing and those appropriate to modern control design methods are discussed. The importance of obtaining input and output matrices in modal testing is emphasized, and the changes that may be needed in modal testing procedures to meet the needs of the control system designer are addressed. Directions for future research are considered.

Description: This paper describes the testing aspects and the problems encountered during the free-free and fixed base modal surveys completed on the original Space Station Common Module Prototype (CMP). The CMP is a 40-ft long by 14.5-ft diameter 'waffle-grid' cylinder built by the Boeing Company and housed at the Marshall Space Flight Center (MSFC) near Huntsville, AL. The CMP modal survey tests were conducted at MSFC by the Dynamics Test Branch. The free-free modal survey tests (June '90 to Sept. '90) included interface verification tests (IFVT), often referred to as impedance measurements, mass-additive testing and linearity studies. The fixed base modal survey tests (Feb. '91 to April '91), including linearity studies, were conducted in a fixture designed to constrain the CMP in 7 total degrees-of-freedom at five trunnion interfaces (two primary, two secondary, and the keel). The fixture also incorporated an airbag off-load system designed to alleviate the non-linear effects of friction in the primary and secondary trunnion interfaces. Numerous test configurations were performed with the objective of providing a modal data base for evaluating the various testing methodologies to verify dynamic finite element models used for input to coupled load analysis.

Description: A Mars Aerial Platform (MAP) mission capable of generating thousands of very-high-resolution (20 cm/pixel) pictures of the Martian surface is considered. The MAP entry vehicle will map the global circulation of the planet's atmosphere and examine the surface and subsurface. Data acquisition will use instruments carried aboard balloons flying at nominal altitude of about 7 km over the Martian surface. The MAP balloons will take high- and medium-resolution photographs of Mars, sound its surface with radar, and provide tracking data to chart its winds. Mars vehicle design is based on the fourth-generation NTP, NEP, SEP vehicle set that provides a solid database for determining transportation system costs. Interference analysis and 3D image generation are performed using manual system sizing and sketching in conjunction with precise CAD modeling.

Description: An attitude control law is derived to realize linear unforced error dynamics with the attitude error defined in terms of rotation group algebra (rather than vector algebra). Euler parameters are used in the rotational dynamics model because they are globally nonsingular, but only the minimal three Euler parameters are used in the error dynamics model because they have no nonlinear mathematical constraints to prevent the realization of linear error dynamics. The control law is singular only when the attitude error angle is exactly pi rad about any eigenaxis, and a simple intuitive modification at the singularity allows the control law to be used globally. The forced error dynamics are nonlinear but stable. Numerical simulation tests show that the control law performs robustly for both initial attitude acquisition and attitude control.

Description: The design, analysis, and simulation of a control law that guarantees a fine pointing performance under external disturbances and model uncertainties are investigated. The authors examine the achievable performance and modeling errors for the control-structure interaction (CSI) evolutionary model structure and highlight the importance of accurate knowledge of structural frequencies and damping values for very lightly damped structures. Numerical results indicate that a limited but significant line-of-sight pointing performance robustness can be attained in spite of modeled structured and unstructured uncertainties in the system. The simulation results reported demonstrate typical performance levels, types of uncertainties and their magnitudes, and design tradeoffs for a realistic laboratory model of a large flexible space structure.

Description: A state space model for the Hubble Space Telescope under the influence of unknown disturbances in orbit is presented. This model was obtained from flight data by applying the Q-Markov covariance equivalent realization identification algorithm. This state space model guarantees the match of the first Q-Markov parameters and covariance parameters of the Hubble system. The flight data were partitioned into high- and low-frequency components for more efficient Q-Markov cover modeling, to reduce some computational difficulties of the Q-Markov cover algorithm. This identification revealed more than 20 lightly damped modes within the bandwidth of the attitude control system. Comparisons with the analytical (TREETOPS) model are also included.

Description: A group of fifteen students in the Electrical Engineering Department at the University of Maryland, College Park, has been involved in a design project under the sponsorship of NASA Headquarters, NASA Goddard Space Flight Center and the Systems Research Center (SRC) at UMCP. The goal of the NASA/USRA project was to first obtain a refinement of the design work done in Spring 1986 on the proposed Mobile Remote Manipulator System (MRMS) for the Space Station. This was followed by design exercises involving the OMV and two armed service vehicle. Three students worked on projects suggested by NASA Goddard scientists for ten weeks this past summer. The knowledge gained from the summer design exercise has been used to improve our current design of the MRMS. To this end, the following program was undertaken for the Fall semester 1986: (1) refinement of the MRMS design; and (2) addition of vision capability to our design.

Description: The topics are presented in view graph form and include the following: an adaptive model following control; adaptive control of a distributed parameter system (DPS) with a finite-dimensional controller; a direct adaptive controller; a closed-loop adaptively controlled DPS; Lyapunov stability; the asymptotic stability of the closed loop; and model control of a simply supported beam.