Abstract
Twin-roll cast magnesium has a fine-grained microstructure and exhibits relatively high strength and ductility. However, hydrogen-induced embrittlement in magnesium alloys can limit the mechanical properties substantially and can lead to sudden and unpredictable failure. In this study, embrittlement is determined by means of slow strain rate tests (SSRT) and instrumental indentation tests (IIT). The latter enables analysis of embrittlement under the suppression of crack propagation mechanisms and surface influences (e.g. notch effects due to pitting) and is a new technique for the investigation of hydrogen embrittlement (HE). In this study, the influence of immersion time and elastic deformation on the HE of twin-roll cast and heat-treated magnesium sheets (AZ31) was analysed. Distilled water and two NaCl solutions (0.05 and 0.5 wt%) served as analysing media. It is shown that both influencing factors significantly affect the rate and the degree of HE. Relatively short immersion in distilled water led to a substantial decrease in strain and an increase in brittleness, even without external mechanical loading. In contrast, strength was not affected by immersion in water and the resulting HE. In comparison to immersion in distilled water, immersion in sodium chloride solution led to a total loss of plasticity and a decrease in strength during SSRT without a distinct increase in embrittlement during IIT. Analysis by X-ray diffractometry did not determine a detectable amount of magnesium hydrides in the embrittled AZ31 structure.
Similar content being viewed by others
References
Stampella RS, Procter RPM, Ashworth V (1984) Environmentally-induced cracking of magnesium. Corros Sci 24:325–337
Winzer N, Atrens A, Song G, Ghali E, Dietzel W, Kainer KU, Hort N, Blawert C (2005) A critical review of stress corrosion cracking (SCC) of magnesium alloys. Adv Eng Mater 7:659–693
Zeng RC, Zhang J, Huang WJ, Dietzel W, Kainer KU, Blawert C, Wei K (2006) Review of studies on corrosion of magnesium alloys. Trans Nonferr Met Soc China 16:763–771
Argade GR, Yuan W, Kandasamy K, Mishra RS (2012) Stress corrosion cracking susceptibility of ultrafine grained AZ31. J Mater Sci 74:6812–6822. doi:10.1016/j.corsci.2005.02.017
Winzer N, Atrens A, Dietzel W, Raja V, Song G, Kainer KU (2008) Characterisation of stress corrosion cracking (SCC) of MgAl alloys. Mater Sci Eng 488:339–351
Winzer N, Atrens A, Dietzel W, Song G, Kainer KU (2008) Fractography of stress corrosion cracking of MgAl alloys. Metall Mater Trans A 39A:1157–1173
Winzer N, Atrens A, Dietzel W, Song G, Kainer KU (2007) Stress corrosion cracking in magnesium alloys: characterization and prevention. JOM 59(8):49–53
Lynch S (2012) Hydrogen embrittlement phenomena and mechanisms. Corros Rev 30:105–123
Lynch S (2012) Mechanistic and fractographic aspects of stress corrosion cracking. Corros Rev 30:63–104
Kannan MB, Dietzel W, Zeng R, Zettler R, dos Santos JF (2007) A study on the SCC susceptibility of friction stir welded AZ31 Mg sheets. Mater Sci Eng A 460–461:243–250
Song RG, Blawert C, Dietzel W, Atrens A (2005) A study on stress corrosion cracking and hydrogen embrittlement of AZ31 magnesium alloy. Mater Sci Eng A 399:308–317
Yao X, Zhu ZH, Cheng HM, Lu GQ (2008) Hydrogen diffusion and effect of grain size on hydrogenation kinetics in magnesium hydrides. J Mater Res 23:336–340
Fairman L, West J (1965) Stress corrosion cracking of a magnesium aluminium alloy. Corros Sci 5:711–716
Fairman L, Bray HJ (1971) Intergranular stress corrosion cracking propagation in magnesium alloys. Br Corros J 6:170–174
Schimmel H, Kearley G, Huot J, Mulder F (2005) Hydrogen diffusion in magnesium metal (alpha phase) studied by ab initio computer simulations. J Alloy Compd 404–406:235–237
Nishimura C, Komaki M, Amano M (1999) Hydrogen permeation through magnesium. J Alloy Compd 329:293–295
Kannan MB, Dietzel W, Blawert C, Atrens A, Lyon P (2008) Stress corrosion cracking of rare-earth containing magnesium alloys ZE41, QE22 and Elektron 21 (EV31A) compared with AZ80. Mater Sci Eng A 480:529–539
Chen J, Wang J, Han E, Ke W (2008) Effect of hydrogen on stress corrosion cracking of magnesium alloy in 0.1 M Na2SO4 solution. Mater Sci Eng A 488:428–434
Chen J, Ai M, Wang J, Han E, Ke W (2009) Stress corrosion cracking behaviors of AZ91 magnesium alloy in deicer solutions using constant load. Mater Sci Eng A 515:79–84
Nozaki T, Hanaki S, Yamashita M, Uchida H (2003) Proceedings of 13th Asian-Pacific Corrosion Control Conference, Osaka, K15
DIN EN ISO 14577-1 Metallic materials-Instrumented indentation test for hardness and material parameters-Part 1 Test method (ISO/DIS 14577-1:2012), Beuth Verlag GmbH, 2012
Janakiraman N, Aldinger F (2010) Indentation analysis of elastic and plastic deformation of precursor-derived Si–C–N ceramics. J Eur Ceram Soc 30:775–785
Abidin NIZ, Martin D, Atrens A (2011) Magnesium corrosion in different solutions. Mater Sci Forum 690:369–372
Moriwaki T, Akahama Y, Kawamura H, Nakano S, Takemura K (2006) Structural phase transition of rutile-type MgH2 at high pressures. J Phys Soc Jpn 75:074603
Shi Z, Atrens A (2011) An innovative specimen for Mg corrosion studies. Mater Sci Forum 690:365–368
Ebtehaj K, Hardie D, Parkins RN (1988) The influence of chloride-chromate solution composition on the stress corrosion cracking of a MgAl alloy. Corros Sci 28:811–821
Acknowledgements
The authors thank the Saxon State Ministry for Economic Affairs, Labour and Transport, the Development Bank of Saxony, in particular, as well as the European Social Fund for their financial support of the project 080943441.
Conflict of interest
The authors declare that they have no conflict of interest.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Tuchscheerer, F., Krüger, L. Hydrogen-induced embrittlement of fine-grained twin-roll cast AZ31 in distilled water and NaCl solutions. J Mater Sci 50, 5104–5113 (2015). https://doi.org/10.1007/s10853-015-9064-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-015-9064-3