ALBERT

Description: We consider levitation of an axisymmetric drop of molten glass above a spherical porous mould through which air is injected at a constant velocity. Owing to the viscosity contrast, the float height for a given shape is established on a much shorter time scale than the subsequent deformation of the drop under gravity, surface tension and the underlying lubrication pressure. Equilibrium shapes, in which an internal hydrostatic pressure is coupled to the external lubrication pressure through the total curvature and the Young-Laplace equation, are determined using a numerical continuation scheme. The set of solution branches is surprisingly complicated and shows a rich bifurcation structure in the parameter space ( Bo =ρg V2/3/γ, Ca = μav/γ), where Bo is bond number and Ca is capillary number, ρ and V are the drop density and volume, γ the surface tension, μa the air viscosity and v the injection velocity. The linear stability of equilibria is determined using a boundary-integral representation for drop deformation that factors out the rapid vertical adjustment of the float height. The results give good agreement with time-dependent simulations. For sufficiently large Ca there are intervals of Bo for which there are no stable solutions and, as Ca increases, these intervals grow and merge. The region of stability decreases as the mould radius aM increases with an approximate scaling Ca∼aM-5, which imposes practical limitations on the use of this geometry for the manufacture of lenses. © 2008 Cambridge University Press 2008.

Description: Microdroplet deposition is a technology that spans applications from tissue engineering to microelectronics. Our new high-speed imaging measurements reveal how sequential linear deposition of overlapping droplets on flat uniform substrates leads to striking non-uniform morphologies for moderate contact angles. We develop a simple physical model, which for the first time captures the post-impact dynamics drop-by-drop: surface-tension drives liquid redistribution, contact-angle hysteresis underlies initial non-uniformity, while viscous effects cause subsequent periodic variations. © 2014 Cambridge University Press.

Description: We examine the sensitivity of Saffman-Taylor fingers to controlled variations in channel depth by investigating the effects of centred, rectangular occlusions in Hele-Shaw channels. For large occlusions, the geometry is known to support symmetric, asymmetric and oscillatory propagation states when air displaces a more viscous fluid from within the channel. A previously developed depth-averaged model is found to be in quantitative agreement with laboratory experiments once the aspect ratio (width/height) of the tube's cross-section reaches a value of 40. We find that the multiplicity of solutions at finite occlusion heights arises through interactions of the single stable and multiple unstable solutions already present in the absence of the occlusion: the classic Saffman-Taylor viscous fingering problem. The sequence of interactions that occurs with increasing occlusion height is the same for all aspect ratios investigated, but the occlusion height required for each interaction decreases with increasing aspect ratio. Thus, the system becomes more sensitive as the aspect ratio increases in the sense that multiple solutions are provoked for smaller relative depth changes. We estimate that the required depth changes become of the same order as the typical roughnesses of the experimental system for aspect ratios beyond 155, which we conjecture underlies the extreme sensitivity of experiments conducted in such Hele-Shaw channels. © © 2016 Cambridge University Press This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution, and reproduction in any medium, provided the original work is properly cited..

Description: Motivated by the reopening mechanics of strongly collapsed airways, we study the steady propagation of an air finger through a collapsed oil-filled channel with a single compliant wall. In a previous study using fully compliant elastic tubes, a 'pointed' air finger was found to propagate at high speed and low pressure, which, if clinically accessible, offers the potential for rapid reopening of highly collapsed airways with minimal tissue damage (Heap & Juel Phys. Fluids, vol. 20 (8), 2008, 081702). The mechanism underlying the selection of that pointed finger, however, remained unexplained. In this paper, we identify the required selection mechanism by conducting an experimental study in a simpler geometry: a rigid rectangular Hele-Shaw channel with an elastic top boundary. The constitutive behaviour of this elasto-rigid channel is nonlinear and broadly similar to that of an elastic tube, but unlike the tube, the channel's cross-section adopts self-similar shapes from the undeformed state to the point of first near wall contact. The ensuing simplification of the vessel geometry enables the systematic investigation of the reopening dynamics in terms of increasing initial collapse. We find that for low levels of initial collapse, a single centred symmetric finger propagates in the channel and its shape is set by the tip curvature. As the level of collapse increases, the channel cross-section develops a central region of near opposite wall contact, and the finger shape evolves smoothly towards a 'flat-tipped' finger whose geometry is set by the strong depth gradient near the channel walls. We show that the flat-tipped mode of reopening is analogous to the pointed finger observed in tubes. Its propagation is sustained by the vessel's extreme cross-sectional profile at high collapse, while vessel compliance is necessary to stabilise it. A simple scaling argument based on the dissipated power reveals that this reopening mode is preferred at higher propagation speeds when it becomes favourable to displace the elastic channel wall rather than the viscous fluid. © 2017 Cambridge University Press.

Description: Accurate low-dimensional models for the dynamics of falling liquid films subject to localized or time-varying heating are essential for applications that involve patterning or control. However, existing modelling methodologies either fail to respect fundamental thermodynamic properties or else do not accurately capture the effects of advection and diffusion on the temperature profile. We argue that the best-performing long-wave models are those that give the surface temperature implicitly as the solution of an evolution equation in which the wall temperature alone (and none of its derivatives) appears as a source term. We show that, for both flat and non-uniform films, such a model can be rationally derived by expanding the temperature field about its free-surface values. We test this model in linear and nonlinear regimes, and show that its predictions are in remarkable quantitative agreement with full Navier-Stokes calculations regarding the surface temperature, the internal temperature field and the surface displacement that would result from temperature-induced Marangoni stresses. © The Author(s) 2019. This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence.

Description: We consider the propagation of an air finger into a wide fluid-filled channel with a spatially varying depth profile. Our aim is to understand the origin of the multiple coexisting families of both steady and oscillatory propagating fingers previously observed in experiments in axially uniform channels each containing a centred step-like occlusion. We find that a depth-averaged model can reproduce all the finger propagation modes observed experimentally. In addition, the model reveals new modes for symmetric finger propagation. The inclusion of a spatially variable channel depth in the depth-averaged equations leads to: (i) a variable mobility coefficient within the fluid domain due to variations in viscous resistance of the channel; and (ii) a variable transverse curvature term in the dynamic boundary condition that modifies the pressure jump over the air-liquid interface. We use our model to examine the roles of these two distinct effects and find that both contribute to the steady bifurcation structure, while the transverse curvature term is responsible for the distinctive oscillatory propagation modes. © 2014 Cambridge University Press.

Description: Flow of a thin viscous film down a flat inclined plane becomes unstable to long-wave interfacial fluctuations when the Reynolds number based on the mean film thickness becomes larger than a critical value (this value decreases as the angle of inclination to the horizontal increases, and in particular becomes zero when the plate is vertical). Control of these interfacial instabilities is relevant to a wide range of industrial applications including coating processes and heat or mass transfer systems. This study considers the effect of blowing and suction through the substrate in order to construct from first principles physically realistic models that can be used for detailed passive and active control studies of direct relevance to possible experiments. Two different long-wave, thin-film equations are derived to describe this system; these include the imposed blowing/suction as well as inertia, surface tension, gravity and viscosity. The case of spatially periodic blowing and suction is considered in detail and the bifurcation structure of forced steady states is explored numerically to predict that steady states cease to exist for sufficiently large suction speeds since the film locally thins to zero thickness, giving way to dry patches on the substrate. The linear stability of the resulting non-uniform steady states is investigated for perturbations of arbitrary wavelength, and any instabilities are followed into the fully nonlinear regime using time-dependent computations. The case of small amplitude blowing/suction is studied analytically both for steady states and their stability. Finally, the transition between travelling waves and non-uniform steady states is explored as the amplitude of blowing and suction is increased. © 2015 Cambridge University Press.