ISSN:
0003-3146
Keywords:
Chemistry
;
Polymer and Materials Science
Source:
Wiley InterScience Backfile Collection 1832-2000
Topics:
Chemistry and Pharmacology
,
Physics
Description / Table of Contents:
Sphärische makroporöse Partikel, die als Trägermaterialen für verschiedene Säulen-Operationen eingesetzt werden sollen, wurden mittels Suspensions- und Mikrosuspensionspolymerisation von Trimethylolpropan-trimethacrylat (TRIM) in Gegenwart verschiedener Mengen porogener Reagenzien (Toluol bzw. Mischungen von Toluol und Isooktan) hergestellt. Textur und Eigenschaften der Partikel variierten deutlich mit dem Anteil und der Zusammensetzung des porogenen Reagens und wurden zusätzlich durch die Wahl des Suspensionstabilisators beeinflußt. Die makroporösen Partikel wiesen ein Gesamtporenvolumen von 0,4 bis 3,6 cm3/g und eine spezifische Oberfläche von 7 bis 〉 450 m2/g auf. Alle Partikel enthielten Makroporen und, außer den Teilchen mit sehr niedriger spezifischer Oberfläche, einen gewissen Anteil an Mikroporen (Durchmesser 〈 60 Å). Durch Erniedrigung der Monomerkonzentration und Erhöhung des Isooktan-Gehaltes im porogenen Reagens auf 50 Gew.-% konnte das Auftreten von Mikroporen vollständig unterdrückt werden. Das Erhöhen des Isooktan-Gehaltes führte zu einem vergrößerten Gesamtporenvolumen und zu einem verringerten Quellvermögen der Polymermatrix in Toluol. Der Einfluß einer Hitzebehandlung bei 130°C und eines Aufpfropfens von Polymethylmethacrylat auf die Partikeleigenschaften wurde ebenfalls untersucht.Die Menge an nicht umgesetzten Doppelbindungen in den Partikeln konnte durch Variation der Polymerisationstemperatur verändert werden. Das Vorhandensein leicht zugänglicher Doppelbindungen ist wichtig, da sie zur Funktionalisierung der festen makroporösen Partikel verwendet werden können.
Notes:
Spherical macroporous particles, intended for use as carrier particles in various types of column operations, were prepared by suspension and microsuspension polymerization of trimethylolpropane trimethacrylate (TRIM), in the presence of various amounts of porogenic agents (toluene or mixtures of toluene and isooctane). The texture and properties of the particles varied markedly with the amount and composition of the porogenic agent, and were also affected by the choice of suspension stabilizer. Macroporous particles were prepared, ranging in total pore volume from 0.4 to 3.6 cm3/g, and in specific surface area from 7 to 〉450 m2/g. All of the particles contained macropores, and except for those with very low specific surface area, contained a certain fraction of micropores (diameter 〈60 Å). The presence of micropores could be eliminated completely by decreasing the monomer concentration and increasing the isooctane content of the porogenic agent to 50 wt.-%. Increasing the isooctane content also resulted in an increase in the total pore volume and a decrease in the tendency of the polymer matrix to swell in toluene. The effect on properties of particles by heat treatment at 130°C and by grafting poly(methyl methacrylate) onto the particles was also studied.The amount of unreacted double bonds of the particles could be varied by varying the polymerization temperature. The presence of easily accessible double bonds is important as they can be utilized for functionalization of the rigid macroporous particles.
Additional Material:
11 Ill.
Type of Medium:
Electronic Resource
URL:
http://dx.doi.org/10.1002/apmc.1991.051920110
Permalink