ALBERT

Description: Time-reverse imaging is a wave propagation algorithm for locating sources. Signals recorded by synchronized receivers are reversed in time and propagated back to the source location by elastic wavefield extrapolation. Elastic wavefield extrapolation requires a P-wave as well as an S-wave velocity model. The velocity models available from standard reflection seismic methods are usually restricted to only P-waves. In this study, we use synthetically produced time signals to investigate the accuracy of seismic source localization by means of time-reverse imaging with the correct P-wave and a perturbed S-wave velocity model. The studies reveal that perturbed S-wave velocity models strongly influence the intensity and position of the focus. Imaging the results with the individual maximum energy density for both body wave types instead of mixed modes allows individual analysis of the two body waves. P-wave energy density images render stable focuses in case of a correct P-wave and incorrect S-wave velocity model. Thus, P-wave energy density seems to be a more suitable imaging condition in case of a high degree of uncertainty in the S-wave velocity model.

Description: The impact of changes in saturation on the frequency-dependent reflection coefficient of a partially saturated layer was studied. Seismic attenuation and velocity dispersion in partially saturated (i.e., patchy saturated) poroelastic media were accounted for by using the analytical solution of the 1D White's for wave-induced fluid flow. White's solution was applied in combination with an analytical solution for the normal-incidence reflection coefficient of an attenuating layer embedded in an elastic or attenuating background medium to investigate the effects of attenuation, velocity dispersion, and tuning on the reflection coefficient. Approximations for the frequency-dependent quality factor, its minimum value, and the frequency at which the minimum value of the quality factor occurs were derived. The approximations are valid for any two alternating sets of petrophysical parameters. An approximation for the normal-incidence reflection coefficient of an attenuating thin (compared to the wavelength) layer was also derived. This approximation gives insight into the influence of contrasts in acoustic impedance and/or attenuation on the reflectivity of a thin layer. Laboratory data for reflections from a water-saturated sand layer and from a dry sand layer were further fit with petrophysical parameters for unconsolidated sand partially saturated with water and air. The results showed that wave-induced fluid flow can explain low-frequency reflection anomalies, which are related to fluid saturation and can be observed in seismic field data. The results further indicate that reflection coefficients of partially saturated layers (e.g., hydrocarbon reservoirs) can vary significantly with frequency, especially at low seismic frequencies where partial saturation may often cause high attenuation.

Description: We studied seismic attenuation of P- and S-waves caused by the physical mechanism of wave-induced fluid flow at the mesoscopic scale. Stress relaxation experiments were numerically simulated by solving Biot’s equations for consolidation of 2D poroelastic media with finite-element modeling. The experiments yielded time-dependent stress-strain relations that were used to calculate the complex moduli from which frequency-dependent attenuation was determined. Our model consisted of periodically distributed circular or elliptical heterogeneities with much lower porosity and permeability than the background media, which contained 80% of the total pore space of the media. This model can represent a hydrocarbon reservoir, where the porous background is fully saturated with oil or gas and the low-porosity regions are always saturated with water. Three different saturation scenarios were considered: oil-saturated (80% oil, 20% water), gas-saturated (80% gas, 20% water), and fully water-saturated media. Varying the dry bulk and shear moduli in the background and in the heterogeneities, a consistent tendency was observed in the relative behavior of the S-wave attenuation among the different saturation scenarios. First, in the gas-saturated media the S-wave attenuation was very low and much lower than in the oil-saturated or in the fully water-saturated media. Second, at low frequencies the S-wave attenuation was significantly higher in the oil-saturated media than in the fully water-saturated media. The P-wave attenuation exhibited a more variable relative behavior among the different saturation degrees. Based on the mechanism of wave-induced fluid flow and on our numerical results, we suggest that S-wave attenuation could be used as an indicator of fluid content in a reservoir. Additionally, we observed that impermeable barriers in the background can cause a significant increase in S-wave attenuation. This suggests that S-wave attenuation could also be an indicator of permeability changes in a reservoir due to, for example, fracturing operations.