ALBERT

Description: Lithium-sulfur battery (LSB) will become the next generation energy storage device if its severe shuttle effect and sluggish redox kinetics can be effectively addressed. Here, a unique three-dimensional hollow reduced graphene oxide microsphere decorated with ZnO nanoparticles (3D-ZnO/rGO) is synthesized to decrease the dissolution of lithium polysulfide (LiPS) into the electrolyte. The chemical adsorption of ZnO on LiPS is combined with the physical adsorption of 3D-rGO microsphere to synergistically suppress the shuttle effect. The obtained 3D-ZnO/rGO can provide sufficient space for sulfur storage, and effectively alleviate the repeated volume changes of sulfur during the cycle. When the prepared S-3D-ZnO/rGO was used as the cathode in LSB, an initial discharge specific capacity of 1277 mAh g−1 was achieved at 0.1 C. After 100 cycles, 949 mAh g−1 can still be maintained. Even at 1 C, a reversible discharge specific capacity of 726 mAh g−1 was delivered.

Description: Nano-silver paste, as an important basic material for manufacturing thick film components, ultra-fine circuits, and transparent conductive films, has been widely used in various fields of electronics. Here, aiming at the shortcomings of the existing nano-silver paste in printing technology and the problem that the existing printing technology cannot achieve the printing of high viscosity, high solid content nano-silver paste, a nano-silver paste suitable for electric-field-driven (EFD) micro-scale 3D printing is developed. The result shows that there is no oxidation and settlement agglomeration of nano-silver paste with a storage time of over six months, which indicates that it has good dispersibility. We focus on the printing process parameters, sintering process, and electrical conductivity of nano-silver paste. The properties of the nano-silver paste were analyzed and the feasibility and practicability of the prepared nano-silver paste in EFD micro-scale 3D printing technology were verified. The experiment results indicate that the printed silver mesh which can act as transparent electrodes shows high conductivity (1.48 Ω/sq) and excellent transmittance (82.88%). The practical viability of the prepared nano-silver paste is successfully demonstrated with a deicing test. Additionally, the experimental results show that the prepared silver mesh has excellent heating properties, which can be used as transparent heaters.

Description: Overcoming the disadvantages of low transmission and broad peak bandwidth of previously reported plasmonic color filters, a high-efficiency multispectral plasmonic color filter is theoretically proposed with two cascaded ultrathin metallic nanogratings separated by two heterogeneous dielectric layers, and its optical properties are theoretically investigated using the finite-difference time-domain method. The transmission spectrum presents three near-unity peak bands accompanied with three near-null dip bands adjacent around them. Both transmission efficiencies of above 90% and ultranarrow peak bandwidth of 20 nm are achieved in the visible regime. The peak band positions can be flexibly tailored by varying the structural parameters. The filter selects the visible color with high signal noise ratio at the peak bands. The outstanding spectral properties of this filter indicate significant improvement for the high-accuracy color filtering and multispectral imaging applications. The simulated near-field electromagnetic distributions suggest that the excitation of the hybrid antisymmetric surface plasmon polariton (SPP) leaky mode and metal-insulator-metal waveguide modes are responsible for the peak transmission bands, while the formation of the hybrid SPP bound modes confined on the bottom nanograting makes the dip transmission bands, all of which are the consequence of the plasmonic hybridization between the two neighboring metallic nanogratings.

Description: In this study, soymilk was hydrolyzed to different degrees with flavourzyme, and then soymilk and enzyme modified soymilk at various levels were added to skim milk respectively, to generate a mixed gel using rennet. Rheological properties, scanning electron microscopy imaging, and physical and chemical indexes were examined to reveal the effect of enzyme modified soymilk on rennet induced gelation of skim milk. Results showed that soymilk inhibited the aggregation of skim milk, led to a decrease in storage modulus (G’), significantly increased moisture content and curd yield, and the resulting network was coarse. Enzyme modified soymilk with a molecular weight below 20 kDa led to a more uniform curd distribution, which counteracted the reduction of G’ and allowed for the formation of a stronger gel. Both the moisture content and the curd yield increased with the addition of soymilk and enzyme modified soymilk, and overall the effect of adding a high degree of hydrolysis of enzyme modified soymilk was superior. Compared to untreated soymilk, the addition of a certain amount of enzyme modified soymilk resulted in a new protein structure, which would improve the texture of blend cheese.

Description: High-performance engineered structural systems are crucial for sustainable development in the field of construction. In our previous research, a novel steel–concrete composite beam with transverse and longitudinal hidden girders exhibited good flexural behavior and desirable ductility. However, there is a dearth of studies on the flexural response of a steel–concrete composite slab voided with thin-walled core boxes. Therefore, in this study, we investigated the overarching flexural mechanism of the proposed structure when subjected to uniform vertical loads. The experimental detection results illustrated that the deflection value of the composite beam was 95.75% less than the GB/T 50152-2012 recommendation. Numerical results further validated this observation. The recorded data from the strain profile at the mid-span of the frame girder indicated that there was a considerable membrane effect, which delayed the strain growth of rebars, yielding appreciable bearing capacity. Thus, two original approaches to predicting the ultimate load of this novel structure are proposed, considering limit analysis using the upper-bound method and the membrane effect, with the latter closely linked to the experimental results. The findings can promote the extensive application of similar sustainable systems and inspire further advancements in advanced engineering structures.

Description: The occurrence of popular social events causes fluctuations and changes of public emotions, while the rapid development of online social platforms and networks has made individual interactions more intense and further escalated public emotions into public opinion. However, there is a lack of consideration of individual emotions in the current research on online public opinion. Based on this, this paper firstly expounds the quantitative representation of attitude and emotion, analyzes the formation and propagation process of online public opinion by combining individual’s expression willingness, individual’s expression ability, attitude perception value, attitude change probability and other factors, and constructs a network public opinion propagation model that takes individual emotion into consideration. Finally, the main factors affecting the formation and propagation of network public opinion are discussed through simulation experiments. The results demonstrate that: (1) fear is conducive to the formation of online public opinion, but the speed is relatively slow; sadness is not conducive to the formation, but once enough people participate in the exchange of views, the formation of online public opinion will be faster; (2) the influence of online public opinion on individual emotions expands with the increase of the number of individual interactions; (3) different network structures impact differently on the propagation of public opinion. Among them, BA (BA network is a scale-free network model proposed by Barabasi and Albert in order to explain the generation mechanism of power law, BA model has two characteristics: growth and priority connection mechanism) and ER (ER network is a network with random connectivity proposed by Erdös-Renyi) random networks can promote the propagation of online public opinion, which is prone to “one-sided” online public opinion. WS small-world networks (proposed by Watts and Strogatz. It is a kind of network with short average path length and high clustering coefficient) and fully-connected networks have an inhibitory effect on the spread of online public opinion, easily maintaining the multi-dimensional nature of online public opinion.

Description: An electric-field-driven (EFD), μ-3D printed, fused polymer technique has been developed for the fabrication of large-area microscale prototype molds using typical polymer materials, including microcrystalline wax (MC-wax), polycaprolactone (PCL), and polymathic methacrylate (PMMA). This work proposes an alternative for large area microscale modes and overcomes the limitation of high cost in the traditional mold manufacturing industry. The EFD principle enables printing of fused polymers materials more than one order of magnitude lower than the nozzle diameter, contributing to the necking effect of the Taylor cone jet, which is the key factor to achieve the microscale manufacturing. Numerical simulation of electric field distribution between the meniscus and substrate was carried out to elucidate the dependence of electric field distribution on the meniscus condition of three types of polymers under printable voltage, and the electrical field parameters for the EFD μ-3D printing were determined. A number of experiments were printed successfully using a large range of viscosity materials, ranging from tens of mPa·s to hundreds of thousands of mPa·s of PCL and PMMA. The differences in parameters of different materials, such as viscosity, tensile properties, and surface energy, were studied to assess their use in different fields. Using proper process parameters and a nozzle with an inner diameter of 200 μm, three different application cases were completed, including a Wax microarray and microchannel with a minimum dot diameter of 20 μm, a PCL mesh structure with a minimum line width of 5 μm, and a PMMA large-area mold with a maximum aspect ratio of 0.8. Results show that the EFD μ-3D printing has the outstanding advantages of high printing resolution and polymer material universality.

Description: During the COVID-19 pandemic, social education has shifted from face to face to online in order to avoid large gatherings and crowds for blocking the transmission of the virus. To analyze the impact of virus on user experience and deeply retrieve users’ requirements, this paper constructs a reasonable evaluation index system through obtaining user reviews about seven major online education platforms before and after the outbreak of COVID-19, and by combining the emotional analysis, hot mining technology, as well as relevant literature. At the same time, the variation coefficient method is chosen to weigh each index based on the difference of index values. Furthermore, this paper adopts the comprehensive evaluation method to analyze user experience before and after the outbreak of COVID-19, and finally finds out the change of users’ concerns regarding the online education platform. In terms of access speed, reliability, timely transmission technology of video information, course management, communication and interaction, and learning and technical support, this paper explores the supporting abilities and response levels of online education platforms during COVID-19, and puts forward corresponding measures to improve how these platforms function.

Description: As a traditional Chinese medicinal drink, Apocynum venetum, a local tea from Xinjiang, China, is favored for its rich flavor and biological functionality. This study looked at aging mice induced by d-galactose to determine the in vivo anti-aging effect of Apocynum venetum tea extracts (AVTEs) and its bioactive components. We evaluated the weight of major organs (via organ index) and pathological changes in the liver. We also detailed the effects of AVTE (250 mg/kg in the low dose group, 500 mg/kg in the high dose group) on biochemical parameters (malondialdehyde, superoxide dismutase, glutathione, glutathione peroxidase, catalase, total antioxidant capacity, and nitric oxide) and cytokines (IL-6, IL-12, TNF-α and IL-1β) in the serum of aging mice. We investigated the anti-aging effects of AVTE in d-galactose-induced aging mice via quantitative real-time reverse transcription-polymerase chain reaction (RT-qPCR) assay. In addition, we analyzed the biological components of AVTEs by high performance liquid chromatography (HPLC). The results were remarkable, suggesting that AVTE significantly improved d-galactose-induced aging mice, with the high dose group showing the best results among other groups. ATVE can effectively alleviate hepatocyte edema, as well as inflammatory cell infiltration and injury in mice, induce a protective effect via up-regulation of glutathione (GSH), glutathione peroxidase (GSH-Px), superoxide dismutase (SOD), and catalase (CAT) antioxidant related factors, and play an important role in the up-regulation of anti-inflammatory factors (IL-10) and the down-regulation of pro-inflammatory factors (IL-6, TNF-α and IL-1β). At the same time, HPLC analysis showed that AVTEs contain neochlorogenic acid, chlorogenic acid, cryptochlorogenic acid, rutin, isoquercitrin, isochlorogenic acid B, isochlorogenic acid A, astragalin, isochlorogenic acid C, rosmarinic acid, and trans-cinnamic acid. Thus, AVTE appears to be an effectively functional drink due to its rich functional components and anti-aging activities.